您要查找的是不是:
- The measures of control welding residual deformation. 控制焊接残余变形的措施。
- The welding residual deformation is the crucial influential factor in the design integrality,the rational manufacturing techniques and the service durability of welding structures. 焊接的非平衡加热、冷却过程导致产生焊接应力与变形,而焊接残余变形是影响结构设计完整性、制造工艺合理性和结构使用可靠性的关键因素。
- The reasons of welding residual deformation 焊接残余变形的因素
- Keywords weldment;welding residual deformation;welding technology; 焊接结构;焊接残余变形;焊接工艺;
- welding residual deformation 焊接残余变形
- New idea to control welding residual stress and distortion with trailing impactive electromagnetic force was given. 提出了基于脉冲电磁力随焊控制焊接应力及变形新方法。
- Using finite element program-ABAQUS,the welding residual stress of tube-to-tubesheet joint in heat exchangers had been numerically simulated. 利用有限元软件ABAQUS,对换热器管子与管板焊接残余应力进行数值模拟,获得了焊接接头残余应力的分布规律,比较了伸出角接头和内角接头的优劣。
- The successful application of explosion treatment on relieving welding residual stress in S belt of hot-blast stove in WIS(G)CO is introduced. 介绍了消除焊接残余应力爆炸处理技术在武钢高炉热风炉上的成功应用。
- The residual deformation around the hole was measured by digital speckle correlation technique and the relation curves of residual strain at the side of hole vs fatigue life cycles were obtained. 再应用数字散斑相关技术测量了不同疲劳循环次数后孔周的残余变形场,并给出了孔边最大残余应变与疲劳循环次数的关系曲线。
- Abstract :Many components of TC4 titanium alloy should be manufactured by EBW in aeronautic industry, but the researches of weld residual stress for those were few at present. 摘要:航空领域中许多钛合金构件需要采用电子束焊接加工制造,但对其焊后的残余应力分布状况,目前研究较少。
- Relier of welding residual stress by using strip-shaped dynamite has been investigated on low-carbon steel, low-alloy steel, quenched and tempered steel and autstenite steel. 用条状炸药对碳钢、低合金钢、调质钢和奥氏体不锈钢进行爆炸消除焊接残余应力试验。
- A two-dimensional axial-symmetric finite-element model of welding residual stresses of thick-wall pipe has been proposed based on the theory of thermal-elastoplasticity. 以热-弹塑性理论为基础,建立了厚壁管环焊残余应力的二维轴对称有限元模型,利用ANSYS有限元分析软件,模拟了耐热钢厚壁管环焊对接的应力分布。
- In this paper, weld residual stress of GH536 superalloy components with EBW were measured by Mathar method. Test results showed that residual stress is low in the weld and its distribution accords with the traditional rules. 针对航空发动机GH536合金材料,采用小孔法对其电子束焊接试板的残余应力分布趋势进行测试研究,试验结果表明,焊缝区存在较低的应力峰值,且应力分布符合传统规律。
- ground surface residual deformation 地表残余变形
- The uncertain factors in the welding residual stresses measurement by blind hole technique are analyzed with the fuzzy mathematic method to evaluated the strain release factor A and B. 摘要在分析一些引起盲孔法检测焊接残余应力测量误差的不确定因素的基础上,引入模糊数学方法对应变释放系数进行评价。
- But the thickness of the coatings may be heterogeneous since the effect of the weld residual high during coating spiral-welded pipes, which will influence the service life of the coated pipe line. 但在螺旋焊缝钢管涂敷过程中,由于受到焊缝馀高的影响,防腐层可能会出现厚薄不均的现象,这将影响防腐管道的寿命。
- The unbonded high-strength strand used in the concrete columns can minimize the residual deformations effectively. 在混凝土柱中配置预应力无粘结钢绞线可以有效控制残余变形。
- The calculating of welding residual stress establish the base of fatigue life analysis, offers the gist for considerig the affect of welding residual stress in the design of runner. 焊接残余应力计算为后续的转轮疲劳寿命分析奠定基础,同时为转轮的设计阶段考虑焊接残余应力的影响提供依据。
- A finite element simulation was performed of the multi-pass welding residual stress of Hastelloy-C276 alloy pipes using ABAQUS software based on the welding characteristics of Hastelloy C276 alloy. 针对哈氏合金C276焊接特点,运用有限元分析软件ABAQUS,对哈氏合金C276管道多道焊残余应力进行了有限元模拟。利用单元生死技术,模拟焊缝金属的形成;利用FORTRAN语言编写子程序DFLUX,实现了移动的高斯分布热源;
- Despite microsurgical repair of the brachial plexus during early infancy, residual deformities of the shoulder, elbow,and hand are often noted. 尽管在婴儿早期进行了臂丛的显微外科修复,在肩、肘及手部仍会残留畸形。
