您要查找的是不是：
- The result indicated that the material removal rate of isopulse generator is over 20% higher than that of general pulse generator. 实验结果表明，与普通脉冲电源相比,等能量脉冲电源可以提高加工效率20%25以上。
- This paper proposed a viewpoint to explain why vibration assistance may increase material removal rate (MRR) in vibration-assisted finishing process. 摘要讨论振动研磨加工过程中通过辅助振动提高材料去除率的原因。
- Experiment results showed that WEDM in atmosphere offers advantages such as better straightness,shorter gap length and higher material removal rate. 实验结果表明,气中加工的直线度好、放电间隙窄、加工速度(材料去除率)高。
- Experiment results showed that WEDM in atmosphere offers advantages such as better straightness and higher material removal rate. 实验结果表明,气中线切割加工具有加工表面直线度好、加工速度(材料去除率)高等优点。
- Both high material removal rate(MRR) and smooth surface have to be achieved in primary chemical mechanical polishing(CMP) of hard disk substrates. 硬盘盘基片粗抛光必须在较高材料去除率的基础上获得高表面质量。
- Larger diamond crystals and greater diamond protrusion will result in a potentially faster material removal rate when there is enough horsepower available. 金刚石晶体和金刚石突较大将导致更大更快的物质可能有足够的去除率马力刊物。
- With the optimized normal rake angle, machining force and temperature change less, but material removal rate is improved obviously with increasing cutting speed. 通过优化刀具前角，提高切削速度，切削力和切削温度变化较小，但是显著提高了材料去除率。
- The polishing pad is main consumables of the CMP system, the structure and surface roughness of pad have great effects on the material removal rate and surface roughness of wafer. 抛光垫是化学机械抛光(CMP)系统中的主要耗材之一，抛光垫的结构和表面粗糙度对CMP过程中的硅片材料去除率和表面粗糙度有很大影响。
- Ultrasonic is applied in slider lapping. Experiment show that material removal rate and the roughness of surface are improved. The pole tip recession (PTR) is reduced. 在硬盘磁头抛光中加入超声波,可以提高材料去除率、降低表面粗糙度值、减小极尖沉降。
- It is concluded that when the silicon and pad rotate with the same rotational velocity, the material removal rate (MMR) is proportional to the rotational velocity. 当晶片和垫板的转动角速度相同时，得出材料去除率(MMR)与垫板和晶片相对速度成正比的结论。
- A system for adaptive optimization of cutting parameters such as feed rate and spindle speed in a face milling operation for maximizing the material removal rate without violating machining constraints is set up. 基于以上算法 ,构造了平面铣削加工参数自适应优化系统 ,可使加工系统在不违反加工约束的前提下 ,总是获得最大材料去除率。
- The results show that under the same lapping conditions the Si3 N4 ball has the lowest material removal rate and the best roundness and roughness, followed by ZrO2, Al2O3, and SiC ball. 结果表明：在相同的研磨条件下，具有长柱状晶粒的氮化硅陶瓷球加工速率最低，但圆度和表面粗糙度最容易控制；氧化锆和氧化铝陶瓷球表面质量次之，碳化硅陶瓷球加工速率最高，圆度和表面粗糙度最难控制。
- It is indicated that the optimal nonuniformity of wafer surface and material removal rate can be obtained under the wafer and the pad rotating in the same direction with the equal rotational speed. 分析结果表明：硅片与抛光垫转速相等转向相同时可获得最佳的材料去除非均匀性及材料去除率。
- Normally as a result, material removal rates and therefore dicing speed is lowered and the laser capability with respect to the available power is far from optimized. 通常情况下，剥离速度和切割速度都是很低的。基于其本身的能力来讲，激光器没有运行在最优化的状态下。
- Material Removal Rate Study of Wire Electrical Discharge Machining Pocketing 线电极放电铣削凹坑的材料去除率规律研究
- Effect on material removal rate of fluid jet polishing by several parameters 液体喷射抛光时各工艺参数对材料去除量的影响
- Let' s take the metal removal rate for example. 让我们以金属切削速率为例。
- The function and the acceptance condition of maximum material requirement (MMR) and reversible requirement (RR) were analyzed through dynamic tolerance figure. 通过动态公差图，分析了最大实体要求(MMR)及其可逆要求(RR)的功能及合格条件。
- Scraps or material removed when something is trimmed. 剪削，废料从被修剪的东西上掉下来的碎屑
- The removal rate of NH3-N was up to 73.3%. 在脱氮模式中氨氮的去除率达到了73.;3%25；
