您要查找的是不是：
- H4 composite had a better tensile modulus. 拉伸模数H4组成为最佳。
- The tensile strength for cast of the formula is 107.4MPa and the tensile modulus 4.05GPa. 配方浇铸体的拉伸强度为 10 7.;4MPa;拉伸模量为4
- The tensile strength decreases and the tensile modulus increases after the carbonized PAN-CF is graphitized. 与炭化样品相比,PAN-CF石墨化后的拉伸强度减小,拉伸模量增大;
- The tensile modulus of the nano-meter composites prepared from No. 2 LDH and PA6 was 26.8% higher than that of pure PA6. 其中2号水滑石与尼龙6复合后拉伸模量与尼龙相比提高了26.;8%25。
- The tensile strength,bending strength,impact strength,tensile modulus of elasticity and bending modulus of elasticity were determined. 测试了塑木板材的拉伸强度、弯曲强度、冲击强度、拉伸弹性模量、弯曲弹性模量等力学性能;
- With the content of 5%wt ultrafine calcium carbonate, tensile strength of PP is 33.68MPa, tensile modulus is 1.38GPa, izod impact strength is 9,38KJ/m2. 超细碳酸钙改性聚丙烯时，在5%25wt左右力学性能达到最佳，拉伸强度可以达到33.;68MPa，弹性模量可以达到1
- Tensile strength , tensile modulus at 300% , hardness ect became better when the epoxide degree is higher . Elongation at break of EBR is much better than BR . Themechanical properties of EBR-30 approachs BR . EBR硫化胶的拉伸性能、300%25定伸应力、硬度等物性指标随环氧值的增加而升高，而扯断伸长率则远远高于BR，EBR-30物性指标接近BR。
- When the contents of KH550-treated attapulgite and EOC-g-MAH is 10% and 15% respectively,compared with crude EOC,100% tensile modulus,tensile strength and tear strength of AT/EOC composites increase by 104%,65%,25% respectively. 当经KH5 5 0处理的凹凸棒石为 10份 ,接枝率为 0 89%25的EOC g MAH为 15份时 ,复合材料的 10 0%25拉伸模量、拉伸强度和撕裂强度分别比EOC弹性体提高 10 4%25、65%25、2 5%25。
- The effect of the nano-meter Ti-alloy particle on the tensile modulus, tensile strength, elongation at break, notched impact strength and yield strength of the compositie was also studied. 研究了钛合金粉体对复合材料拉伸模量、拉伸强度、断裂伸长率、冲击强度及屈服强度的影响。
- The results showed that with the increase of heat treatment temperature,both the carbon content and tensile modulus of carbon fibers were enhanced,however the linear density decreased. 试验结果表明,随着热处理温度的提高,炭纤维线密度下降,微晶层间距缩小,碳含量、微晶尺寸和拉伸模量得以提高。
- The longitudinal tensile strength and the longitudinal tensile modulus of elasticity were investigated for moso bamboo (Phyllostachys pubescens) at different heights and radial positions. 将毛竹轴向分段(4段)、径向分层(6层)取样,研究其顺纹抗拉弹性模量和顺纹抗拉强度的变异规律,顺纹抗拉性质与气干密度之间的关系。
- FACTORS EFFECTING 300% TENSILE MODULUS OF SBR-1500 影响丁苯橡胶SBR-1500300%25定伸应力的因素
- tensile modulus of elasticity parallel to grain 顺纹抗拉弹性模量
- Elongation at break decreases and tensile moduli increases with the PVC increase. 两种增容剂增容的体系，随着PVC加入量的增加，拉伸强度下降不明显、断裂伸长率随着PVC的增加而降低，在50 wt%25以前冲击强度保持较高数值，之后显著下降，弹性模量随着PVC的增加而增加。
- Predicting Method for Tensile Modulus of Stitching Laminate by Finite Element Analysis 基于均匀化方法的缝纫层压板拉伸弹性模量有限元预测
- Another basic quantity is the bulk modulus K. 另一个基本的量是体积模量K。
- Keywords moso bamboo（Phyllostachys pubescens）;air-dried density;tensile modulus of elasticity;tensile strength; 毛竹;气干密度;顺纹抗拉弹性模量;顺纹抗拉强度;
- The heat treatment improves the tensile strength. 热处理能提高抗拉强度。
- This shape allows only tensile strain. 这种形状使膜片只允承受拉伸压力。
- The circumferential normal stress is tensile. 周向正应力是张性的。
