您要查找的是不是：
- zone of welding current 焊接电流调节范围
- When the welding current is added, the fusion quality of welding stick will increase, so the weld reinforcement also will increase. 焊接电流增加时,焊丝的熔化量也增加,因此焊缝的余高也随之增加。
- It is successfully applied in de-noising of welding current，and actual welding current signals are attained. 并成功应用于焊接电流信号的滤波分析处理，得到了真实的焊接电流信号。
- Double-frequency cipher can solve the problem of multimachine mutual interference fairly good by handling the remote control and autocorrection of welding current. 采用“双频密码”方式解决焊接电流的远程调节及自动修正，较好地处理了多机相互干扰问题。
- With the microchip of PHILIPS 80C552,the controller realizes the functions of welding program control,welding current wave control and trouble-shooting. 控制器基于PHILIPS的80C552单片机设计,具有焊接程序控制、焊接电流波形调制、故障诊断等功能;
- Continuous adjusting and matching of welding voltage-current with LED digital display, presetting and indicating of welding current, voltage and tractor speed available. 焊接电压、电流连续可调与匹配，设有数显电流/电压表，可预设及显示焊接电流、电压及小车行走速度.
- Through flexible software, different given signal of welding current was outputted by the single chip microcomputer system, which can control the welding current. 通过软件的灵活编制，单片机控制系统可按要求输出不同的焊接电流给定信号，从而来控制焊机的输出电流波形。
- This paper presents the development of technology of welding current remote control and concentrates on the principle of a stepless wave carrier welding current remote controller. 叙述了焊接电流遥控技术的发展，详细论述了无级载频式焊接电流遥控器的原理。
- The nonuniformity of structure and mechanical properties was most critical in weld zone of welded jointthat is weakest zone in the joint. 该焊接接头中的熔合区组织和力学不均匀性最为严重，是该焊接接头最薄弱的部位。
- Gets the time zone of the current computer system. 获取当前计算机系统的时区。
- Secondly, the method and process of the design of fuzzy controller in which welding current error and the changing rate of welding current error is used as fuzzy inputs, and the increment of the controlling angle of SCR as fuzzy output. 其次，介绍了以焊接电流误差、焊接电流误差变化率为输入，可控硅控制角增量为输出的模糊控制器设计方法与过程。
- Will be in the current time zone of the system. 将基于系统的当前时区。
- Through the acquisition of welding currents and voltages during welding,the arc behavior of welding process was analyzed. 对焊接过程的电流及电压波形进行采集,分析焊接过程的电弧行为。
- By a method of recording of welding currents and time,the information of joint microstructure and properties can be gained according to the welding time with different currents. 利用微机检测焊接电流和时间,运用统计方法获得在不同焊接电流区间的焊接时间,间接给出焊接接头组织性能的状态。
- Below the water table is the zone of saturation. 潜水面以下就是饱水带。
- It is a zone of abnormal pressure. 这是异常压力层。
- A zone of abnormal pressure has been drilled into. 钻入了异常压力层。
- And the special economic zone of Shantou. 和经济特区汕头学汉语。
- Remain the position of welding clamp in advance. 留出焊接夹具的位置
- THE EQUIPMENTS AND FIXTURE OF WELDING LINE. 焊装线设备及工装夹具
