您要查找的是不是：
- In order to obtain cubic boron nitride thin films the working gas pressure must be appropriate, otherwise the cubic phase can not be synthesized. 在其他条件不变的情况下,研究了工作气压对制备立方氮化硼薄膜的影响。
- The influence of the technical parameters such as substrate temperature, O2:Ar, working gas pressure and sputtering power on the photoelectric properties of samples was studied and analyzed. 研究分析了基片温度、氧氩比O2:Ar、工作气压、溅射功率等工艺参数对样品的光学性能和电学性能的影响。
- Under otherwise equal conditions, the film deposition ratio by UMS is higher and more influenced with working gases pressure than by MS. 相同工艺条件下，非平衡模式下薄膜沉积速率高于平衡模式，且更易受到氩气流量变化的影响。
- Influence of Working Gas Pressure on the Preparation of Cubic Boron Nitride Thin Films 工作气压对制备立方氮化硼薄膜的影响
- Influence of the working gas pressure on the deposition rate in magnetron sputtering for thin coating 磁控溅射镀膜中工作气压对沉积速率的影响
- Keywords magnetoelastic thin film;stress-impedance;working gas pressure;bias field;annealing; 磁弹性薄膜;应力阻抗;溅射气压;偏置场;退火处理;
- Influence of work gas pressure on field emission characteristics for BN thin films 工作气压对氮化硼薄膜场发射特性的影响
- They measure gas pressure five times per hour. 他们每小时测量五次气压。
- Gas pressure due to the materials inside the star. 第一种向外压力是恒星物质所造成的。
- Gas pressure gauge and fill valve. 气体压力表及充气阀。
- working gas pressure 工作气压
- The gas pressure is adjusted so as to balance the beam. 通过调整气体的压力可以使天平横梁平衡。
- Then the gas pressure builds up until the volcano erupts. 这样，气体压力就会越来越大，以致引起火山爆发。
- As the pressure coefficient increases, the volume ratio of the working gas vs. the cushion gas increases rapidly and the efficiency of gas storages increases too. 同时随著增压系数的增大，工作气与气垫气的体积比迅速增加，气库效率随之提高。
- Under the condition of meeting HCD effect, the smaller the dimension of cavityis aud the pressure of work gas, the higher the discharge voltage. 在满足空心阴极效应的条件下,空腔尺寸越小,放电电压和工作气压越高,加热功率越大。
- WOG=water,oil,gas pressure, WSP=working stream pressure. 600WOG表示英制球阀，150WSP表示压力，具体参数不明！
- Fabrication process and working principle of thermal gas pressure sensors based on a surface-machining micro-hotplate(MHP) are presented. 给出了采用牺牲层技术制作的微热板式气压传感器的加工工艺和工作原理。
- Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings (08. 增塑的环氧树脂气压管和配件规范(08。
- AUTOMATIC KNIFE INPUT DEVICE; GAS PRESSURE CONTROL, EASY TO BE OPERATED. 自动进刀装置，采气压控制，方便操作。
- It might entail soap testing to make leaks visible when gas pressure is used. 当使用气压试漏时，可以使用肥皂水来目测是否有泄露。
