您要查找的是不是：
- withstand test voltage 耐压试验电压
- At the end, the high voltage withstand test is made, and the working-pressure of the lift is measured. 最后，对绝缘升降平台进行了耐压试验，并对平台升降时水平油缸的工作压力进行了测量。
- Based on the analysis of insulation structure and experience, it is proved that touse AC voltage withstand test being stead of DC voltage withstand test is necessary and possible. 根据绝缘结构分析和实践经验证明尽快执行用交流极间耐压代替直流耐压的新标准的必要性、紧迫性和可行性。
- The resistor is first measured with test voltage V1, giving R1. 首先在测试电压V1之下测量电阻器，得到R1。
- induced over voltage withstand test 感应耐压试验
- The general Ross announced: anyone in training and withstand test, more than 48 hours will be lowered, and their flag. 校长罗斯将军宣布：任何人在训练中经受不住考验，超过48小时将被除名，并降下本国国旗。
- Test Voltage of Loading at high temperature test is 1.5 Time of the rated voltage. 高温负载试验电压为额定电压的1.;5倍。
- This kind of aesthetic feeling that does not get popular limitation again confirm only the path of the meaningful that economize to avoid running short just is withstand test. 这种不受流行限制的美感再次印证惟有细水长流才是经得起考验的隽永之道。
- De-energize Ch. 42, then open Ch. 1 and close Ch. 2 to apply the test voltage to terminal 3. 释放通道42，然后开路通道1，并闭合通道2，向端子3上施加测试电压。
- With this method, the user enters the test voltage, measurement time and the number of iterations. 使用这个方法，用户输入测试电压、测量时间和重复次数。
- The voltage rating of these resistors must be at least equal to the test voltage. 这些电阻器的电压额定值必须至少等于测试电压。
- Next, it is measured with test voltage V2 (where V2is greater than V1), giving R2. 接着在测试电压V2之下（V2大于V1）测量电阻器，得到R2。
- Note the exponential decay in the current using both a positive and a negative test voltage. 注意在使用正、负测试电压时电流的指数衰减情况。
- On-site AC Voltage Withstand Test of High Voltage XLPE Power Cable 高压交联电缆现场交流耐压试验
- Proposal for AC Voltage Withstand Test for Electric Power Capacitor 关于大容量电力电容器极间交流耐压试验的意见
- This application employs a Model 6517A Electrometer, which can supply the test voltage and measure the residual voltage. 这种应用情况使用了一台6517A型静电计，它能够供给测试电压并测量剩余电压。
- The test voltage shall be the nominal system voltage corresponding to the ballast input voltage rating, as specified in Table 16.3.3.1. 如表16.;3
- Multifunction of testing voltage value, current value, RF value and transient current strength. 多用途测试电压值,电流值,射频值及瞬变电流强度等。
- Spark test voltage values given by the potential difference between the test electrode and the conductor of the core or cable under test shall be specified in the cable standard. 火花试验时,电极与被测试电线或电缆之间的电位差的值在电线标准中有明确规定。
- Withstand Test in Safety Inspection of TV Receiver 电视机安全检验中的抗电强度试验
