您要查找的是不是：
- WC-NiP Alloy Wear Resisting Layer Sintered on the Face of Seal Ring 密封环表面烧复碳化钨-镍磷合金耐磨层的研究
- Application of Repair Welding Technology for The Wear Resistant Layer of Blower Rotor 鼓风机转子耐磨层补焊技术的应用
- Abstract The comprehensive mechanical properties of the heat shears were analyzed and the microstructures and properties of the surfacing high wear resisting alloy layer were studied. 分析了热剪刃的综合力学性能要求，并对表面堆焊高耐磨合金层的显微组织和性能进行了研究。
- Wear resistant ceramics machine parts. 耐磨陶瓷用作机械零件。
- Urumqi Xinzhou Wear Resistant Material Co., Ltd. 新轴耐磨材料有限公司。
- High wear resistance and good toughness properties. 具有高的耐磨性和良好的韧性。
- Excellent strength and toughness, predominantly for large drawing dies, small heading dies and other wear resisting components. 具有优良的强度和韧性,主要用于制作大拉制模,小规格冷镦模具,还可作其他耐磨耗零部件。
- The microstructure,wear resisting and abrasive mechanism of argon arc remelting area of alloyed casting iron camshaft is studied. 研究了合金铸铁凸轮轴氩弧重熔淬火后强化层的组织、耐磨性及磨损机理。
- The wear resistance of hard alloy (YG14) and boronizing layer,boron-chromizing layer for steel 45 was studied. 研究了硬质合金(YG14)和45钢渗硼层、硼铬共渗层的耐磨性。
- The hardness, brittleness and wear resistance of Re Chrome boronized layer and boronized layer are studied. 通过对钢单渗硼层和稀土硼铬共渗层的硬度、脆性和磨损特性进行研究。
- Using the developed numerical simulation software of temperature field, the solidification process of wear resisting cast ball in metal mold was numerically simulated. 利用温度场数值模拟软件对金属型耐磨铸球的凝固过程进行了数值计算。
- The recent development of the additive for PPS wear resisting material is reviewed.The mechanism of the wear behavior of the composite is explained by means of SEM and XPS. 按照耐磨材料的常用添加剂类别对PPS摩擦磨损影响进行了详细的综述，并根据扫描电子显微镜(SEM)和X射线光电子能谱(XPS)等分析对其机理进一步解释。
- CONSTRUCTION:Steel wire spiral reinforced layer, and wear resistant synthetic rubber cover. 结构：由钢丝缠绕骨架层和内外耐油、耐腐蚀合成橡胶组成。
- Being as two layer refractory lining on valve plate and valve body,light mullite and phosphate corundum refractory castables are taken as heat isolation and heat resisting layers respectively. 阀板、阀体的耐火衬里隔热层采用莫来石轻质耐火浇注料、耐热层采用磷酸刚玉质耐火浇注料,进行两层浇注。
- Recommended for important wear resistant structures. 本产品可推广应用于重要的耐磨钢结构。
- When re-install the fire resistant layer core, should guarantee the jointing surfaces are tight and without leakage. 重新安装阻火层芯子时应保证各接合面严密无泄漏。
- The cutting tool must be strong, tough, hard, and wear resistant. 刀具必须具有强度、硬度、韧性和耐磨性。
- Highest wear resistance for low strain of toughness. 具有最高的耐磨性、在低应力条件下具有最好的韧性。
- The blocked fire resistant layer core found when check should be cleaned, to guarantee each pore is unblocked, distorted and corroded fire resistant layer should be replaced. 检查发现被堵塞的阻火层芯子应清洗干净，确保芯子上每个孔眼畅通，对于变形或腐蚀的阻火层应更换。
- For high strain of toughness and good wear resistance. 在高应力条件下具有好的韧性和高的耐磨性。
