您要查找的是不是：
- wall thickness deviation 壁厚度偏差
- Range Min and Max.-OD with wall thickness. 范围分钟和最大Od以壁厚度。
- The design models of blank of tapered wall thickness cone and equal wall thickness cone with deviation from sine law are presented. 同时给出了考虑偏离正弦律强力旋压壁厚和变壁厚锥形件毛坯的设计模型。
- The thickness deviation and minimum individual value shall comply with the values given in table 1. 厚度偏差和最小单值见表1。
- The backing of bearings with greater wall thickness is not copper-plated. 轴承壁较厚的轴承,其背衬不镀铜。
- APACO processes Hardboard, MDF or Chipboard up to a wall thickness of 18mm. 橱柜/壁柜/橱柜门板/人造石厨房台面加工制作.
- Thickness Deviation Diagnosis Expert System (TDD ES) is the real time and on line system based on sensors, the data acquisition and processing are the main portions of TDD ES. 热轧带钢厚差诊断专家系统是基于传感器型的在线实时专家系统，数据采集与处理系统是该专家系统的重要组成部分。
- The forecasted wall thickness was conformed to the experimental result. 预测的壁厚和实验结果吻合得很好。
- A novel modified FFT algorithm sampled with Hanning-window is presented, which can be used for the thickness deviation diagnosis of strip and roll eccentricity compensation. 摘要汉宁窗采样快速傅立叶变换比值算法，可用于带钢厚度偏差的诊断，也可用于板带材的轧辊偏心控制补偿。
- A novel modified FFT algorithm sampled with Hanning-window is presented,which can be used for the thickness deviation diagnosis of strip and roll eccentricity compensation. 汉宁窗采样快速傅立叶变换比值算法,可用于带钢厚度偏差的诊断,也可用于板带材的轧辊偏心控制补偿。
- Chapter Two: This chapter expatiates the main factors which lead to lognitudinal thickness deviation and analyzes thickness adjustment methods and basic principles of AGC on detail. 第二章:阐述了冷轧带钢纵向厚度偏差产生原因,并分析了厚度控制方式和厚度自动控制的基本原理。
- End connection including wall thickness of connecting pipe if weld end and any special flange facings or finishes. 连接方式,如果是焊接端口和任何法兰面或表面,则包括连接管道的壁厚。
- What is the foundry's checking frequency for control of core shift and wall thickness? 工厂检验芯偏移以及壁厚的频率?
- The tube deformation characteristics on ASSEL mill are deformation concentrating at shoulder and wall thickness in rolling zone increasing. ASSEL轧管机具有台肩集中变形、碾轧段壁厚增厚等特点。
- The wall thickness of a 1-litre bottle preform is 3mm. The cooling time is 10.8s. 1公升的矿泉水瓶瓶坯壁厚3mm，冷却时间便占10.;8秒。
- The wall thickness of a 5-gallon bottle preform is 8mm. The cooling time is 76.8s. 5加仑瓶瓶坯壁厚8mm，冷却时间是76.;8秒。
- When chilled water is used to cool the mould, cycle time is related to wall thickness as follows. 在冰水冷却的条件下，冷却时间与壁厚有以下的关系。
- The aorta wall thickness (AWT) was measured wiht B-mode echocardiography in 128 patients with primary hypertension. B型超声心动图下测量了128例高血压病患者主动脉壁厚度（AWT），同时检测了血脂指标。
- Centrifugal casting, compact structure, free from pinhole porosity and slag, smooth surface and even wall thickness. 高速离心铸造,组织致密,无砂眼、夹渣,表面光滑、壁厚均匀。
- The carotid intima-media wall thickness (IMT), crouse score and plaque incidence were measured. 测量颈总动脉后壁内中膜厚度(IMT),斑块厚度,计算斑块积分及粥样斑块发生率。
