您要查找的是不是：
- Influence of process parameters on spinning force and wall thickness difference of shear spinning 工艺参数对剪切旋压旋压力和壁厚差的影响
- Discussion About Wall Thickness Tolerance and Wall Thickness Difference of Bushing 小议衬套壁厚公差与壁厚差
- wall thickness difference 壁厚差
- Range Min and Max.-OD with wall thickness. 范围分钟和最大Od以壁厚度。
- Cooling time is proportional to the square of wall thickness, but inversely proportional to mould temperature difference. 冷却时间正比于壁厚的平方，但反比于模温温差。
- The boss is the common structure of casting which can easily result in hot spot because of the difference in the wall thickness. 凸台是铸件中比较常见的结构,它常常使得壁厚不均而产生热节,是最容易产生收缩缺陷的部位。
- The backing of bearings with greater wall thickness is not copper-plated. 轴承壁较厚的轴承,其背衬不镀铜。
- APACO processes Hardboard, MDF or Chipboard up to a wall thickness of 18mm. 橱柜/壁柜/橱柜门板/人造石厨房台面加工制作.
- The forecasted wall thickness was conformed to the experimental result. 预测的壁厚和实验结果吻合得很好。
- The effect of pass decrement in cold rolling for can stock on the control of flatness and thickness difference of rolled plate was analyzed. 分析了制罐料冷轧道次的减少对冷轧机在轧制板型和厚差控制方面的影响,结合生产,对辊系参数、厚差控制系统进行优化,轧制产品的厚度精度有较大提高。
- The seismo-electric effect is interpreted based on electrochemistry theories, membrane effect and thickness difference polarization. 摘要从电化学理论、薄膜效应以及浓差极化，解释了震电效应的基本原理。
- Hot rolling is the key factor for controlling transverse thickness difference, especially edge drop, of non - oriented silicon steel. 热轧是控制无取向硅钢成品横截面厚差偏大、尤其是边部减薄显著的关键工序。
- Qiliqiangxin capsule could reduce effectively BP,LVSP,LVEDP,T wave,improve room wall thickness and heart exponent,reduce AngII and ALT,all the paramenters ahd notable difference,composed to those of model group (P<0.05,P<0.01). 芪苈强心胶囊可有效降低血压、左室压、左室末期舒张压、T波;改善室壁厚度和心脏指数;降低血清血管紧张素II及醛固酮水平;与模型组比较均有显著性差异(P<0.;05;P<0
- Then the cross-section thickness difference of finished strip can be controlled quantitatively based on the crown of work roll,distribution of ASU and rolling force. 在钢带的塑性变形和辊系的弹性变形之间建立比例关系,由此可以通过工作辊凸度、ASU分布、轧制力分布,定量的改变成品钢板的横向厚度差。
- Uniformity of the photoresist film, adhesiveness between underlay and glue film, exposal and develop condition of high thickness difference are all solved in the thesis. 在厚胶光刻工艺中重点解决了胶膜厚度的均匀性、胶膜与衬底的粘附性、大厚度差胶层的曝光、显影条件等的优化问题。
- During the same time the thickness of electrodeposited copper foils is not homogeneous and the thickness difference results in the luster difference on copper foils surfa. 研究了阴极辊焊缝处组织与电解铜箔表面上形成的光亮带之间的关系。
- End connection including wall thickness of connecting pipe if weld end and any special flange facings or finishes. 连接方式,如果是焊接端口和任何法兰面或表面,则包括连接管道的壁厚。
- What is the foundry's checking frequency for control of core shift and wall thickness? 工厂检验芯偏移以及壁厚的频率?
- The tube deformation characteristics on ASSEL mill are deformation concentrating at shoulder and wall thickness in rolling zone increasing. ASSEL轧管机具有台肩集中变形、碾轧段壁厚增厚等特点。
- The wall thickness of a 1-litre bottle preform is 3mm. The cooling time is 10.8s. 1公升的矿泉水瓶瓶坯壁厚3mm，冷却时间便占10.;8秒。
