您要查找的是不是:
- The results show that the new endplate give more uniform pressure distribution than traditional endplate, and could be lighter after simple weight reduction. 结果显示本文设计之新型端板,在提供均匀压力之性能上,远高于传统端板,而且经过简单的轻量化后,重量还能低于传统端板。
- uniform pressure distribution 均布型分布
- The results show that when the taper with a certain degree is under U-pattern gas-flow,the pressure distribution along the mainfold is quite uniform with little pressure loss.The volume flux thr... 研究结果表明,具有一定锥度结构的变截面进气总管在U型进气方式时,电池堆沿进气总管长度方向的压力分布比较均匀,压力损失较小,电池堆各单电池的气体流量较其他形式均匀。
- A system of compensators on the hydraulic circuit provides uniform pressure on the surface of the leather even where the thickness differs. 液压回路中的补偿装置,使厚度不均匀的皮张在各部能受到均匀的压力。
- Metal lacing eyelets for optimum fastening and pressure distribution. 最好加速和减压的金属网状小孔。
- Using ANSYS,we calculate a multi-layered structure with uniform pressure,the result indicate this transformation is cor rect and feasible. 并利用ANSYS软件对层合结构进行有限元分析,结果表明此转换是可行的。
- This curvature of the flow field alters the pressure distribution and the aerodynamic forces from their values in translational flight. 流场的弯曲使压力分布和空气动力与直线飞行时的值相比发生了变化。
- In addition, the isotropic response and deviatoric response of the specimen under uniform pressure are properly described from various plots of different layers and 3-D deformations. 而从不同层面及三维变形图之结果,亦可适度地描述试体在受压情形下整个等向与偏向之反应。
- In addition, the effect of startup pressure gradient of Bingham fluid in stratum pressure distribution are analyzed. 分析了宾汉流体的启动压力梯度对地层压力分布的影响。
- The heavy fogs of Shangqiu are formed by the weather situations: continental anticyclone,warm zone in front of cold front,uniform pressure field,and low pressure with an inverted trough. 商丘市的大雾多形成在大陆高压型、冷锋前暖区型、均压场型、(低压)倒槽型天气形势中。
- The analysis of the hydrostatic pressure distribution is beased on the momentum exchange equation of varying mass. 在动量恢复方程的基础上,分析了主流道的静压分布。
- In this paper, pressure distribution of gaseous slip flow in parallel plates microchannel was studied. 对平行平板微型槽中气体滑移流动的压强分布特性进行了研究。
- For the PTD flow field, this thesis first presents inviscid flow solution of evolved pressure distribution. PTD内部流场问题,先不考虑黏性进行计算,并讨论PTD内部在不同时间的压力分布。
- To enhance close contacting and uniform pressuring during large area and curved surface imprinting, PDMS mold and gas pressure are employed in this study. 此外气体具有均匀且等向之特性,在大面积及非平面基材上施压具有良好的效用,因此两者合并应用的研究就显得更为重要。
- Flue gas flow model is established based on gas flow to research the pressure distribution along the width of furnaces. 运用气体流动相关知识,建立炉气流动模型,研究沿炉宽方向上的压力分布。
- The results show that the pressure distribution on external surface at both windward and leeward is basically the same. 结果表明:车体迎风面及背风面表面压力分布规律基本一致,验证了数值模拟计算模型的准确性;
- Firstly,the pressure distribution of gas solid flow along the circulating route is analyzed and experimentally studied. 分析气固两相流在循环路径中的压力分布,并通过试验对其进行了研究。
- The cone shape can be described by analyzing pressure distribution around a well. 通过研究近井的压力分布描述油井附近的水锥形态。
- The temperature and pressure distribution of the fluids along the pipeline and wellbore are calculated. 结果表明,随着地面注汽管线和井深的增加,过热蒸汽的过热度和压力明显下降。
- The method is used to obtain solutions of large deflections, membrane and bending stresses of circular plates with movable and immovable edges under uniform pressures or a central point load. 本文用微分求积法进行了圆板(考虑面内固定和可动两种情况)在均布载荷和中心集中载荷作用下的大挠度分析,获得了相应的位移、膜应力和弯曲应力分布。