您要查找的是不是：
- The top surface in an enclosed space of a ship. 顶板密闭的船舱的顶层。
- A surface defect in paper. Alternative terms: blisters; foam marks. 中义纸张的表面缺陷，参考字：气泡痕迹。
- Surface defect and macrostructure of high carbon steel billet were analyzed. 介绍了铸坯相关表面缺陷及低倍组织,提出了质量控制措施及方案。
- Perianth pentagonal on top surface, margin narrowly winged. 花被五角的在上表面，边狭翅。
- Perianth 4- or 5-lobed, spongy in fruit, flat on top surface. 花被4或5浅裂，在果期海绵状，在上表面上平。
- Verify that attaching nuts are below top surface of glass adjustment brackets. 验证配合螺帽在玻璃调节支架的上表面的下方。
- In general, the top surface of the beam is acted upon by transverse loads. 横向载荷作用一般认为在梁的顶面上。
- Exterior measurement includes specification and size, surface defect, and sewing requirement. 外观质量包括规格尺寸及公差、表面疵点、缝制要求。
- Zinc content in the alloy above 0. 05% consistently resulted in an unacceptable surface defect as galvanizing. 锌含量低于0．05%25时，型材一般不发生雪花状腐蚀。
- Perianth top surface flattened in fruit, pentagonal, with 4 membranous teeth. 花被上表面在果期使变平，五角，具4膜的牙齿。
- Surface defect detection is important to ensure the utility,integrality,and security of the products. 产品表面缺损检测对保证产品的使用性能、完整性和安全性具有重要意义。
- Perianth top surface flattened in fruit, pentagonal, with 4 small teeth. 花被上表面在果期使变平，五角，用4小的牙齿。
- The article describes the problem of the toughened glass' surface defect and the method of prevention and solution. 针对钢化玻璃表面质量存在的变形点缺陷,采取相对应措施预防和解决。
- Small and superficial occlusal surface defect ,proximal and labial surface defect uninvolved incisal angle . 2 .;合面缺损范围小而且表浅，前牙邻、唇面缺损未涉及切角者，不宜用嵌体修复。
- Using flexible interpolator pad is an important way to suppress the part surface defect in stretch-farming process on multi-paint tool. 摘要采用柔性垫层是抑制和消除多点模拉形过程中零件表面缺陷的重要措施。
- This paper analyzes the reason that caused the surface defect of billet produced by EAF Steelmaking plant of Nanjing Iron and Steel Co.Ltd. 分析了南(京)钢电炉厂小方坯表面质量问题及产生的原因,涉及结晶器振动参数、保护渣等。
- Objective: To provide anatomic basis for repairing the knee joint surface defect with the pedicled patella translocation. 摘要目的：为带血管蒂髌骨移位修复股骨髁和胫骨髁关节面缺损提供解剖学基础。
- Converyer load lower top surface and turn table made of stainless steel fordurability and ease in cleaning. 马达负荷量低、面板、转盘板输送带采用不锈钢制品、不生锈、耐用、清洁、保养容易。
- Using flexible interpolator pad is an important way to suppress the part surface defect in stretch-forming process on multi-point tool. 采用柔性垫层是抑制和消除多点模拉形过程中零件表面缺陷的重要措施。
- If a pore gets blocked but stays open, the top surface can darken and you are left with a blackhead. 而如果毛孔堵塞但没有关闭，毛孔的表面颜色就会加深，黑头粉刺就出现了。
