您要查找的是不是：
- It can increase the hole inclination angle range and drill elevation angle holes, while setting the top drive power head and hole top plate toward the opposite direction. 动力头及孔口板调转方向,可直接钻凿仰孔,大大增加钻孔倾角范围。
- The top plate dismantling beforehand system in cast-in-place shear wall structure provides a practical method. 而现浇剪力墙结构顶板早拆体系为解决这些问题提供了一个可行的方法。
- Automatic tracking the cutting speed: do not need to change the cutting angle if the glass ribbon speed changed. 切割速度自动跟踪：玻璃带速度发生变化，不需要改变切割角度。
- By appending a support board at thebottom of top plate in worktable, the whole rigidity is improved. 在工作台上板的下端增加了支撑板，使整体刚度得到了提高。
- In the paper sliding-cutting angle and cutting angle were calculated,other major cutting parameters were given. 文中计算了滑切角,切割角等主要切割参数,给出了新型剖半机的主要技术参数。
- Abstract: The top plate of basement of Shenzhen West Red-tree Project was designed as a planted and impounded roof. 摘要：深圳红树西岸工程地下室顶板空中花园设计为种植及蓄水屋面。
- At the time Influences of cut angle in indicated power, COP and discharge temperature is studied in details, too. 同时还详细分析和研究了排气通道上斜切口角度对压缩机制冷量、输入功率、性能系数、排气温度等的影响 ,为滚动转子式压缩机的优化和性能提高奠定基础
- If you notice that the top plate is slightly warped in a downward fashion along the edge adjacent to the armboard, this is normal. 播放以前听过多次的唱片，整个声音发生了明显的变化，声音的质感提高不少，小提琴的运弓力度和琴箱的共鸣声明显加强，那种声音是自己非常喜欢的。。。
- The expressions of dihedral angle and cutting angle of the intersecting groove are deduced by way of space analytical geometry. 利用空间解析几何原理推导了多管、板相贯坡口的两面角和实际切割角的表达式,建立了切割多管、板相贯坡口的数学模型。
- Today, the market again in the 7th by hailun line support, quick upside afternoon, the final is still close at a red disc, coal or the top plate. 今天大盘再次在7号操盘线受到了支撑,午后快速上攻，最终仍然以红盘报收，煤炭板块涨幅靠前。
- A quartz crystal has crystallographic axes, and crystal cut is defined according to the cutting angle against a crystallographic axis and its associated mode of vibration. 温频特性与切割角有关，每个石英晶体具有结晶轴，晶体切割是按其振动模式沿垂直于结晶轴的角度切割的。
- Using the programmable controller in the automobile rear axle house ring stiffener,logic sequential control was realized in the top plate automatic welding craft. 采用可编程控制器在汽车后桥壳加强环、后盖自动焊接工艺中实现逻辑顺序控制。
- The influence of air cutting angle and air cutting time to chip breakage is studied quantitatively.The correctness of air cutting theory is verified by the experiments. 定量分析了间断切削过程中的空切角度、空切时间对断屑的影响，并通过试验验证了用空切理论分析断屑的正确性。
- The top plate is stressed when fitted into the wooden plinth, for better resonance control, and transmission of unwanted energy.You are now ready to set up the suspension. 在两位大虾的指导下，悟出了一个道理，任何系统的声音没有对和错，只有自己喜欢与否，耳朵收货：）在此感谢两位大虾的指教。
- The reasonable ranges of the geometrical parameters are given by analyzing the influences of the vertex angle and cutting angle on impact force and penetration displacement. 通过分析棱柱杆的几何参数对撞击力和侵入位移的影响，给出了棱柱杆主要几何参数的合理范围。
- Summary: Numerical control cutting line used in opening and plating cutting coil into exact size sheet and stowing. 横剪线概述:数控板开卷校平剪切线,主要用于将卷板进行开卷、校平、切边、精密定尺剪切成各种规格的板材,并整齐堆垛。
- An experimental IR thermographic method for the evaluation of surface temperature distribution of the top plate is adopted to show the convective heat transfer effects of nanofluids. 藉由红外线热影像实验方式来探讨流道内奈米流体强制热对流现象对盘面温度分布之影响。
- Substantial experience in CNC plates cutting and Robot Profile Cutting such as Programming, Production, Logistics and Workshop Organization and Management. 具有CNC板材切割和机械手仿形切割的设计、生产、后勤和车间的组织和管理方面的丰富经验。
- Due to its relative small losses, theoretically it is supposed to get 50% of conversion effi. ciency at a pump level of 600 mW by using a BBO crystal with cutting angle of 27.030 and length of 10mm. 从分析其性能出发通过计算指出，使用BBO晶体获得倍频426nm蓝光(切割角度为27.;430，长度为10mm)，虽其非线性转换系数小，但由于该晶体的损耗小，在泵浦功率约为600mW时。 理论上同样可以得到50%25的倍频转换效率。
- I used scrap Lexan to hold the plates in the jaws of a Vice-Grip.Dimple the top plate of the stack at the center of the hole. 制作动片组的接触片, 切下一长条防水板，其长度应足够长，能覆盖到动片组轴孔两侧。
