您要查找的是不是：
- tooth profile angle error 齿形角误差
- Suitable Design of Tooth Profile Angle of Transition Edge for Round-head Gear Hob for Pregrinding Hobbing 圆头留磨滚刀过渡刃齿形角的合理设计
- Keywords postgrinding steps transiting curve of toothroot tooth profile angle of transiting edge; 磨后台阶;齿根过渡曲线;过渡刃齿形角;
- tooth profile angle 齿形角
- We are able to offer the tooth profile of chain and sprocket. 我们有能力提供各种形链和链轮。
- Keywords built-up hob;tooth profile reground error;optimium machining angle; 圆磨法滚刀;齿形重磨误差;最佳工艺角;
- The equations of thecurvature,curvature radius on hypocycloid"s tooth profile are deduced. 在此基础上分析推导了各种型式的滚子链谐波传动的传动比计算公式。
- It is proofed with experiment that these is local sunken point in th e raised tooth profile of involute gear. 试验验证渐开线齿轮凸齿形上确实存在局部凹状。
- This paper discussed the relationship between the involute pitch of tooth root and tooth profile involute in hobbing. 本文阐述了滚刀滚齿时齿轮齿根过渡曲线的延长渐开线的等距线与齿轮齿形渐开线的关系。
- Regrinding of hob and gear tooth profile error 滚刀的重磨与齿形误差
- Research on the tooth profile error of gear shaving 剃齿加工齿形误差的研究
- Based on the tooth profile curve equation of inner rotors in cycloidal pump, the formula for displacement calculation of the pump are derived. 根据摆线泵内转子的齿廓曲线方程,推导出了摆线泵的排量计算公式。
- Secondly, steering angle error and steering time are measured when the bottom angle and steering arm length of steering mechanism are varied. 其次，分析了机构底角和转向臂长度两个变量对汽车转向轮转角误差及转向时间的影响。
- The shaving stock of preshaving gears has direct influence on the shaving effect and the tooth profile of preshaving cutters. 剃前齿轮的留剃量形式直接影响剃齿效果及剃前刀具齿形。
- Corner Cube Reflector (CCR) was widely used, but the automatic test of the dihedral angle error of CCR was not realized. 锥体棱镜应用广泛，但其二面角偏差没能实现测量的自动化。
- At last, the tooth profile is measured and the errors in tooth profile and aptness are evaluated by three coordinate measurement machine. 最后,利用三坐标测量机对进行仿真的锥齿轮廓面进行了测量,并评定了齿轮的齿形和接触迹误差,同时进行了齿轮副接触区域的运转实验。
- This paper also presents a method to solve the tunnel axis displacement on line caused by angle error between tube center axis and datum of joint. 分析了对接面与管段中心线夹角误差对沉放后线路位置的影响，提出了控制隧道轴线偏差的措施；
- During ausform finishing process of hardened gears, there is plastic displacement of metal on the tooth surface and the distortion of tooth profile . 在齿轮热滚挤加工中,轮齿上的金属在强制挤压力的作用下沿齿面产生塑性流动,使齿形发生变化。
- Chamfering process of gear tooth profile and its function are introduced. By tooth profile chamfer, noise of gear transmission can be reduced. 通过对齿轮传动噪声产生原因的分析,介绍运用齿轮倒棱工艺,降低噪声的工艺方法及应用。
- As for retroreflector with circular section, FFDP under different incident conditions of laser beam, dihedral angle error and flatness error is simulated. 基于角反射器的几何结构模型, 采用矢量形式的折反射定律, 建立了在不同光束入射条件下, 具有二面角和面形误差的角反射器的出射光场的相位分布和远场衍射模式的数学模型。
