您要查找的是不是：
- The results showed that tool shape had the most influence on tensile shear strength of spot,welding time was secondary,and then tool shoulder. 试验结果表明,搅拌头形状对焊点剪切强度的影响最显著,其次是焊接时间,搅拌头轴肩直径的影响最小。
- In this paper, the effect of talcum powder and nm-montmorillonite(MMT) as fillers on the tensile shear strength of under water epoxy adhesive was reseached. 主要研究了滑石粉、有机化处理蒙脱土作为填料对水下环氧胶粘剂拉伸剪切强度的影响及蒙脱土与滑石粉协同作用效果,依此推荐了水下环氧胶粘剂的组份。
- The results showed that the tensile shear strength of the epoxy construction adhesive was firstly increased and then decreased with increasing the thermal cycles. 结果表明随着热循环次数的增加,环氧结构胶粘剂的拉伸剪切强度呈现先增强而后减弱的趋势。
- The interlaminar shear strength of the composites was characterized by a short beam interlaminar shear test and a double edge-notched tensile shear test. 短梁剪切失效模式为假塑性，而拉剪失效模式为非假塑性破坏。
- Keywords triethylborane;methyl methacrylate;high density polyethylene;adhesion;tensile shear strength; 三乙基硼;甲基丙烯酸甲酯;高密度聚乙烯;黏结;拉伸剪切强度;
- tensile shear strength 剪切强度
- Determination of The Tensile Shearing Strength of Epoxy Paint Film on Metal Surface 金属表面环氧漆漆膜拉伸剪切强度的测定
- Strength properties are commonly referred to as tensile strength, bending strength, compressive strength, torsional strength, shear strength and fatigue strength. 强度性能一般涉及到抗张强度，弯曲强度，耐压强度，抗扭强度，切变强度和疲劳强度。
- The BP neural network is established to predict the compressive strength,the flexural strength,the tensile strength and the shear strength of steel fiber reinforced concrete at minus temperature. 利用BP网络对负温钢纤维混凝土的实验所得到的抗压强度、抗折强度、抗拉强度、抗剪强度进行了仿真预测。
- Touch and close fasteners - Determination of longitudinal shear strength. 粘接拉链。纵向剪切强度的测定。
- tensile shearing strength 拉剪强度
- The results show that the shear strength of COF is higher than that of COG. 结果表明 :COF比 COG的剪切强度高 .
- Keywords weldbonding;tensile shear;strength; 胶焊;拉伸剪切试验;强度;
- The shear strength of the composite is improved above to 11 MPa from 5.5MPa. 改性后碳 /聚芳基乙炔复合材料的剪切强度由 5 5MPa提高到 11MPa以上
- The shear strength of COG and COF bonded with ACF is studied by impact test. 摘要采用冲击试验方法研究了各向异性导电胶膜(ACF)互连的玻璃和柔性基板上倒装芯片（COG和COF）的剪切结合强度。
- The adhesive should preferably have a shear strength greater than 30 mpa . 粘结膜最好具有大于30毫帕的剪切强度。
- Indirect methods to measure the interface bond strength include the interlaminar shear strength test. 测量界面粘结强度的间接方法包括层间剪切强度试验。
- Ambitious attempts to improve interlaminar shear strength have been made by Mueller Prosen and by Keogh. 米勒·普罗森还有基奥都对提高层间切变强度作了大胆的尝试。
- The tensile and shear strengths of three kinds of adhesives were not different statistically (P>0.05). Furthermore, the release of fluorin ion did not have adverse effect on the adhesive strength of FRA within three months. 3种粘接剂之间抗张粘接强度和抗剪粘接强度均没有统计学差异 (P >0 .;0 5 );且在 3个月的时间内;FRA中氟离子的释放没有对FRA的粘接强度产生不利的影响。
- Variation Rule of Shear Strength Index When Direct Shear Test of Coarse-grained Soil. 粗粒土直接剪切试验抗剪强度指标变化规律。
