您要查找的是不是：
- tangential point load 切向点荷载
- Unique 3 point load bearing design for smooth operation. 独特的3点负载支撑结构,有利于平稳运行。
- According to the distortion rectification of eyeglass contour cutting,a new method of calculating tangential point is presented. 研究了工件的变形形式,并依此提出三坐标测量数据的软件矫正法。
- The correction of unstressed length for main cable in saddles and calculation method of tangential point are considered at the same time. 同时考虑了主缆在索鞍处的无应力索长的修正以及切点计算方法;
- This idealization, would however, disguise the fact that the thin web beneath the point load is in danger of buckling. 然而，这个理想化的结构不能指出在集中荷载下面薄腹板处于屈曲危险的现象。
- This idealization would, however, disguise the fact that the thin web beneath the point load is in danger of buckling. 然而,这个理想化的结构不能指出在集中荷载下面薄腹板处于屈曲危险的现象。
- If you start diverging and arguing several tangential points in the same post, you risk confusing the reader. 如果你开始跑题，在同一文中讨论几个不相关的论点，你在冒使读者混淆的风险。
- This paper narrates a kind of microcomputer point load testing system by taking chip microprocessors as main part. 叙述了一种以单片机为主体的微机点载荷测试系统。
- tangential point tracing grinding 切点跟踪磨削
- In order that irregular rock pieces could be used at the site to test the point load strength of rockthe laboratory and the in-situ contrastive testing and analysis are conducted. 为了在现场采用不规则试件测试岩石点荷载强度，在实验室和现场进行了相关的对比测试与分析研究。
- New Concept for Determining the Top Tangential Point on BHA 确定底部钻具组合上切点位置的新观点
- The method is used to obtain solutions of large deflections, membrane and bending stresses of circular plates with movable and immovable edges under uniform pressures or a central point load. 本文用微分求积法进行了圆板（考虑面内固定和可动两种情况）在均布载荷和中心集中载荷作用下的大挠度分析，获得了相应的位移、膜应力和弯曲应力分布。
- Tangential Point Portfolio under Chance-constrained Condition 机会约束下风险证券的期望收益率的切点组合
- On the Tangential Point Tracing Grinding for a Crankshaft Part 切点跟踪磨削法磨削曲轴零件的若干问题探讨
- RESEARCH ON MACHINING ERROR OF TANGENTIAL POINT TRACING GRINDING 切点跟踪磨削法加工误差分析
- RESEARCH ON MOTION MODEL OF TANGENTIAL POINT GRINDING 切点跟踪磨削法运动模型的研究
- Opening displacement of a penny-shaped crack in an isotropic piezoelectric body subjected to arbitrary point loadings. 含币形裂纹的压电体在点力和点电荷作用下的裂纹张开位移。
- After inputting the road-load spectrum, all the rear axle link point loads were calculated, and the highest loads on each joint were obtained. 然后采用后轮道路载荷谱作为输入载荷，再进行仿真分析，得到了最大峰值载荷时各连接点处的载荷。
- Title： Opening displacement of a penny-shaped crack in an isotropic piezoelectric body subjected to arbitrary point loadings. 关键词：币形裂纹;横观各向同性;压电体;裂纹张开位移
- Unique 3 Point Load Bearing Piston Design 独特的3点负载轴承活塞结构
