您要查找的是不是：
- Closed system pressure buildup precautions installed. 关闭已安装的系统压力累计预防装置。
- system pressure consumption 系统压耗
- Please clean crew and passenger oxygen system pressure. 请检查机组和旅客氧气系统的压力。
- With porous wick in the condenser, the system pressure oscillation was reduced. 冷凝器中多孔芯很好地抑制了系统中的温度压力波动现象。
- The system pressure had very big fluctuation during rolling process. 在轧钢过程中系统压力出现大幅度波动。
- A quick reference gauge pointer provides a visual of system pressure. 一个敏感的校准压力指示器显示系统压力。
- Electricity compensates for barometric pressure as well as system pressure variations. 用电补偿大气压和系统压力的变化。
- The system pressure changed the adsorption abilities and pore size distributions of carbide and activated carbon. 反应压力能够改变炭化产物和活化产物的吸附性能和孔径分布。
- By doing so, the DET keeps the system pressure below the relief setting of the Temperature and Pressure relief valve. 通过这种功能，det系列将系统压力保持在温度压力安全阀的排放设置下。
- In the article,the nitrogen and system pressure of underwater hydraulic impulsion shovel was analyzed. 对水下液压冲击铲的氮气室与冲击活塞系统压力进行了分析。
- These tanks maintain system pressure below the relief setting of the relief valve. 这种膨胀罐将系统压力保持在安全阀设置的排放压力以下。
- Monitors exhaust system pressure by sending varying voltages to the onboard computer. 监测废气系统的压力，将各种电压值发送到机载计算机上。
- With porous wick condenser, the system pressure oscillation was reduced largely, even more eliminated. 冷凝器中多孔芯很好的抑制了系统中的温度压力波动现象。
- Analysis results show that hydraulic system pressure presents a linear relation vs. traction increase. 分析结果表明：液压系统的压力随着牵引力的增加，其变化表现为直线关系。
- The valve can be mounted to flanged equipment using Watts Flange Adapters or industry standard grooved coupling, suitable for system pressure and temperatures encountered. 采用适合系统压力和温度的美国瓦茨法兰适配器或行业标准沟槽连接器，这种阀门可以安装到法兰上。
- The valve will then open to discharge steam at the rate or faster than the boiler can generate it, thus restoring system pressure to a safer level. 这是阀门将开启排泄蒸汽，其排泄速度超过锅炉产生蒸汽的速度，因此，可以将系统的压力恢复到安全范围内。
- In view of the increased system pressure, the drive control blocks have to be made from titanium, a high-strength, low-weight metal. 从增大的液压压力来看,驱动控制组件必须由高强度、低重量的金属钛制成。
- Check system pressure after water is heated. If pressure is too high, drain water from boiler and adjust feed water regulator to 12 PSIG. 在水加热后，检查系统压力。如果压力太高，则从锅炉将水排泄出来，并且将进水调节阀压力调节到12PSIG。
- They are not designed to compensate for system pressure fluctuations and should not be used where ASSE 1016 devices are required. 这种阀门不能用来补偿系统压力波动，不能用在要求配置ASSE（美国安全工程师协会）1016认可的设备的地方。
- Following this one hour period, the system pressure shall be reduced to the MAWP of the system and are all welds and joints. 一小时后，将系统压力降至系统的最大许用工作压力，而且这两个步骤的操作要紧密衔接。
