您要查找的是不是：
- suction valve cover 进口阀盖
- The suction valve of NO.3 liner is seized. 3号缸的上水凡尔卡死了。
- Clip cable to cable guide at valve cover. 把电缆夹进阀盖上的电缆导槽。
- Install relief valve cover nut and tighten. 安装安全阀阀盖螺母,并加以紧固。
- Confirm line up, tank outlet and pump suction valve keep free open. 确认流程已通，罐出口及泵入口的阀门保持全开。
- Remove the four screws holding the first check valve cover. 拆卸固定第一止回阀阀盖的四个螺丝。
- Remove the four bolts that hold the relief valve cover in place. 拆卸固定安全阀阀盖的四个螺栓。
- Remove the relief valve cover bolts while holding the cover down. 拆卸安全阀阀盖螺栓,握住阀盖并将其取下来。
- Bite valve cover protects from dirt and debris, includes a bite valve inside. 咬合阀盖保护阀远离灰尘和碎片，包括内置咬气门芯。
- Since scroll compressor has neither suction valve nor clearance, its volumetric efficiency is 90-98%,while that of reciprocating compressors is only 65-75%. 没有吸气阀，没有余隙容积容积效率可以达到90%25-98%25，而多缸活塞式压缩机容积效率只有65%25-75
- Using an appropriate sized wrench, loosen the check valve cover. Unscrew the check valve cover and lift it off. 采用尺寸大小适中的扳手松开止回阀阀盖。宁松止回阀阀盖并将其取出来。
- Lug Style valves cover the bolting the entire length of the body. 凸耳类型阀门配置贯穿整个阀体长度的螺栓连接。
- All detachable parts (eg, hoods and suction valves) should be removed and soaked in a detergent solution. 所有可拆下的部分（罩子和吸引阀门等）应当拆下并浸泡于洗涤溶液中。
- Heavy duty relief valve cover prevents vandalism and protects the valve from damage when the 994HMB is transported to another fire hydrant location. 重型安全阀阀盖，预防故意破坏行为，当994HMB运输到另一个消防栓位置时保护阀门不受破坏。
- When ready to start centrifugal pumps, fully open suction valves and throttle discharge valves of a positive displacement. 当准备好启动离心式泵时，吸入阀全开，容积式排出阀节流。（关于装置开车）
- Remove the relief valve cover, stem/diaphragm assembly, and relief valve spring. 拆卸安全阀阀盖，阀杆/隔膜总成，和安全阀弹簧。
- Engine valve cover mounted with BMC is reduced by 0.7 dB comparing with that mounted with cast aluminum. 配装压铸BMC复合材料和铸铝材料气门室罩的2115型柴油机整机噪声试验也表明:用压铸BMC气门室罩能降低整机A计权声压级噪声0.;7 dB。
- Manufacturer and sales of Silicone Valve Cover Gaskets for the aviation, automotive and motorcycle community. 为航空、汽车与摩托车行业制造与销售硅树脂阀套垫圈。
- The valve cover shall be held in place through the use of a single grooved style two-bolt coupling. 阀盖应该通过单个沟槽状双螺栓联结器固定住。
- The valve cover shall be held in place through the use of a single grooved style two-bold coupling. 这种阀盖应该通过采用沟槽状双螺栓联接器固定在其所在位置上。
