您要查找的是不是:
- stuffing box cover 填料函压盖,填料箱压盖
- Stuffing box finish to 63 RMS or better. 填料箱抛光度达到63RMS以上。
- Gland Eye Bolts: Eyebolts swing aside for ease in repacking the stuffing box. 压盖有眼螺栓:有眼螺栓可以从旁边旋起,使得填料函的填料更换更加容易。
- Stuffing Box ? optional lantern rings and grease injectors are available. 填料函-可配置备选灯笼环和润滑油注射器。
- Stuffing box is integral with agitator base for positive alignment of shaft. 依据混合器轴的实际安装情况,设计一个完整的填料箱。
- Stuffing box is integral with agitator housing for positive alignment of shaft. 依据混合器轴的实际安装情况,一个完整的填料箱。
- Gland Eye Bolts: Eye bolts are securely fastened to the bonnet yet swing away to permit easy access to the stuffing box. 压盖有眼螺栓:有眼螺栓能够安全地紧固阀盖,也可以旋转拆卸,便于方便容易地进入填料函。
- Remove junction box cover that is secured by 3 screws. Place the cover aside and view the wiring diagram on the inside. 通过旋下3个螺丝来拆卸接线盒。把盖子放在旁边并察看内面的接线图。
- Packing: Packing contains corrosion inhibitor to avoid stem pitting. Stuffing box is deep, assuring long packing life. 填料:填料内含防腐剂,避免锈蚀阀杆。深度填料函确保较长的填料使用寿命。
- Stainless steel stuffing box hardware is standard (ie. bolts, gland studs, nuts, washers). 标准的金属密封不锈钢填料箱(如螺栓、填料压盖螺栓、螺母、垫圈)。
- Loosen the screw holding the junction box cover to the top of the water heater. Set the cover aside. 卸下热水器顶部接线盒盖上的固定螺丝。把盖子放在旁边。
- Check the stuffing box, the packing gland should be flatted and the tensioning torque should be proper. 检查填料箱,填料压盖应放平,压紧力要适当。
- The invention discloses a foldable packing box which comprises a box body unit, a containing unit and a box cover unit. 本发明公开一种折叠式包装盒,包含一盒体单元、一容纳单元以及一盒盖单元。
- It has two stem sealing:one is stuffing box and another is toroidal sealing ring (O-ring). 本阀阀杆密封分为两种形式:一为填料密封;一为O型密封环密封。
- The backside of impeller:due to special design of backside impeller,the pressure on the stuffing box is minimum. 叶轮背部:由于叶轮背面的特殊设计,将填料箱上的残余压力减到最小。
- Large stuffing box accommodates all packing arrangements, including live-loaded design and lantern ring type for severe services. 大型填料函可适应所有填料配置排列,包括适用于严酷应用环境的动负载结构和套环。
- The technic characteristics of the TV box cover were analyzed in detail, the mold design,the mold structure charateristics and mold working priciple were stated. 详细分析了制件的使用要求和结构要求,叙述了模具设计的过程,模具的结构特点及模具的动作原理。
- A device, such as the outer sleeve of a stuffing box, designed to prevent a fluid from leaking past a moving machine part. 密封装置,密封套一种装置,比如填充函的外套,设计出来以防止液体从一移动的机器零部件中渗漏出来
- The fracture of stuffing box was caused by fatigue, which resulted from the maximum stress concentration on the centripetal border of the oil hole. 结果表明:材料成分和显微组织均符合要求;裂纹起源于输油孔的侧壁;填料盘的失效模式为疲劳失效,内压在填料盘内部输油孔上产生的应力集中导致了填料盘的疲劳失效。
- It is put forward that the multi-labyrinthic sealing and stuffing box sealing are adopted respectively on the input shaft and output shaft of the reducer. 据此,提出了最佳改造方案:减速箱输入轴采用多重式迷宫密封结构,输出轴采用盘根盒密封结构。