您要查找的是不是：
- stud bolt hole 柱螺栓孔
- Become soon fork fulcrum stud bolt. 变速叉支点螺栓。
- STUD BOLT, 3/4IN X 5IN. A320. GR L7. C/W. 2 NUTS. 每个螺栓配有两个重质半抛光六角螺母。
- Bolt hole fitting plastic core industrial caster. 孔顶塑芯工业脚轮。
- Length of stud bolt dows not include the height of the chamfered part. 双头螺栓长度不包括倒角高度。
- Lug body available with ISO flange dimensions and metric bolt hole threads. 凸耳式阀体符合ISO法兰尺寸和公制螺栓孔螺纹。
- Limited distance deviation of the optional bolt hole on flange shall be 2mm. 法兰上非强制螺栓孔的有限距离偏差应该为2毫米。
- All nozzle flange and girth flange bolts shall be of stud bolt type. 所有设备口法兰及翼缘法兰螺栓应为双头螺栓。
- The bolt holes are in the unit base. 螺栓孔在单元的基部。
- Lug body available with ISO flange dimensions and metric bolt hole threads. For dead-end service use lug style (rated 200 PSI for this service). 凸耳阀体也可配置ISO法兰尺寸和公制螺栓孔螺纹。用于终端位置可采用凸耳结构（此时额定压力为200PSI）。
- It is pointed out that the design of magnetic pulley with large torsional moment is restricted by the contacting structure of circumference between cylinder and end-cover fixed radially by stud bolt. 分析了传统设计的磁滑轮各部件间传递扭矩的情况,指出了圆筒与端盖间圆周面接触径向螺栓紧固的结构方式限制了大扭矩磁滑轮的设计。
- There is standard bolt hole connecting with the valve or bracket.The output axis in the middle is a standard internal octagon. 壳体上有标准的螺孔与阀门或支架相连。中间输出轴为一个标准的内八角。
- Looking for a bolt hole for you and your loved one this Valentine's Day? This selection of romantic retreats should inspire you. 充满充满波西米亚风情的广场酒店，一定会让你流连忘返。不过，要注意你的口袋哦，每天145英镑的花费，应该不算少。
- Position flywheel and O-ring on crankshaft and align bolt holes. 安装飞轮和O形环在曲轴上并对齐螺栓孔。
- Anchor/support bolt holes are located in base of body. 固定器/支架螺栓孔位于阀门的基座。
- The heat - fastening of the stud bolt joint piece 双头螺栓连接副的热紧固
- Centerline of the slot at base of distributor is aligned to centerline of distributor holddown bolt hole on enginIn this position, the holddown bolt should easily pass through slot and into engine. 在分电盘基座上槽的中心线应与引擎上分电盘垂下螺栓孔的中心线对准。在这个位置，垂下螺栓应容易地通过槽进入引擎。
- Stainless steel nuts, slipknot bolts, cap nuts, hex socket bolts, stud bolts, countersunk screws, carriage bolts, hex socket countersunk fasteners and non-standard ones. 不锈钢六角螺丝;螺帽;活接螺丝;盖型螺帽;内六角螺栓;牙条;双头螺丝;沉头螺丝;马车螺丝;沉头内六角;及各种非标;
- Mount restrictor bar into the restrictor bar groove of upper die, mount adjusting bolt for restrictor bar into the bolt hole in the restrictor bar, then mount lower press block, upper press block. 在上模节流棒槽内装入节流棒，将节流棒调节螺栓装配进节流棒的螺丝孔中，再装配上压块。
- The dimension tolerance of bolt holes shall meet the following requirements. 螺栓孔的尺寸公差应满足以下要求
