您要查找的是不是：
- stopper position servo 塞棒位置伺服
- The hardware design and control tactic of the position servo system. 介绍了系统的硬件设计及控制策略。
- Electromechanical Position Servo System (EPSS) is a kind of automatic system used widely. 机电位置伺服系统是一种应用极为广泛的自动化系统。
- This paper presents a digitized DC motor position servo control system based on DSP. 提出一种基于数字信号处理器（DSP）的全数字直流位置伺服控制系统。
- DC motor position servo system is an important component of the digital speed governor system utilized on natural gas engine. 直流电机位置伺服系统是天然气发动机电子调速系统的关键组成部分。
- At last, it establishes RBF neural network based on the electro-hydraulic position servo system, and the results prove the description hereinbefore. 最后以仿真电液位置伺服系统为例,建立相关的RBF网络,验证以上的陈述。
- Based on the Permanent-Magnet Synchronous Motor(PMSM) vector control,the control of position servo system is achieved by using repetitive control(RC). 在永磁同步电机矢量控制的基础上,利用重复控制策略对位置伺服系统进行了控制。
- The equivalent load observed is fed back for resisting force load disturbance and raising the accur acy of the hydraulic position servo control. 利用观测出来的等效负载进行反馈控制，抑制力负载干扰的影响，提高液压位置伺服控制的精度。
- This paper proposes a position servo system based on digital brushless DC motor using TMS320LF2407A Digital Signal Processor (DSP). 摘要基于TMS320LF2407A，建立了无刷直流电机全数字控制系统。
- This paper proposes a state feedback control strategy with a neural network compensator,which is applied in a hydraulic position servo system. 提出一种具有神经网络补偿的状态反馈控制方法并用于液压伺服位置控制系统。
- In the paper,stepping position servo system is introduced in the thesis,and the system s controlling scheme and its structure are analyzed detailedly. 详细地分析了步进式位置伺服系统控制方案及其软硬件结构设计。
- The 16-bits single-chip computer (89C196KC) and resolver are used to realize the position servo control of antenna pointing system. 系统采用89C196KC单片机和多极旋转变压器实现了卫星天线指向系统的位置伺服控制。
- A DC position servo controller used for the laser machine CNC system is introduced which is based on a 80C196 single chip mleroprocessor and made on the industrial PC bus board. 本文介绍一种用于激光加工数控系统的工业PC总线模板式80C196单片机直流位置伺服控制器。
- Aimed at discrete model for pneumatic position servo system, investigation of time-delay and noise polynomial was carried out for improving its control accuracy. 摘要为提高气动位置伺服系统的控制精度，针对其离散模型，分别对时延数和噪声多项式进行研究。
- This paper studies the dynamic characteristics of Electro-hydraulic Position Servo System,and proposes a method of equivalent flow feedback to realize serial control. 针对单回路电液位置伺服系统的动态特性，提出了一种等效流量反馈的控制方法，从而实现了串级控制。
- H.M.Chen, J.P.Su and J.C.Renn,“A Novel Sliding Mode Control of an Electrohydraulic Position Servo System”IEICE Trans.Fundamentals,Vol.E85-A,NO.8 August 2002. 廖麒闵，应用模糊-滑动平面控制于气压伺服系统之研究，国立云林科技大学，硕士论文，2002。
- This paper proposes a new type position controller with neural network structure, gives it ' s learning rule, and do the simulation experiment on position servo system of NC machine. 本文提出了一种新型的神经网络结构的位置控制器,给出了该控制器的学习算法,并进行了数控机床位置伺服系统的仿真实验。
- Roller flattening machine is a pivotal equipment in the material flattening industry.But high-precision hydraulic position servo control roller flattening machine can"t be made in china. 轧辊矫平机是材料平整工业中十分重要的设备，但高精度液压位置伺服控制矫平机国内还属空白。
- For the properties of high nonlinear, low frequency, low stiffness and small damp of pneumatically driven systems, it is difficult to realize high precision position servo control. 摘要由于气压驱动系统本身具有强非线性、固有频率低、刚度低和阻尼小等特点，实现高精度的位置伺服控制比较困难。
- He put the stopper on people borrowing his books without asking. 他不让别人擅自借走他的书。
