您要查找的是不是：
- steering knuckle thrust washer 转向关节止推垫圈
- steering knuckle thrust bearing 转向关节主动轴承
- Note: Valves are static grounded by thrust washer. 注意:这些阀门采用止推垫圈实现静电接地。
- Remove the steering knuckle from the strut. 自支柱拆除转向关节。
- NOTE: Valves are static grounded by thrust washer and packing. 注意:这些阀门通过止推垫圈和填料实现静电接地。
- Route sensor wire from steering knuckle to fender panel. 从转向节到防护板安排感知器导线走向。
- steering knuckle king pin dust washer 转向节主销盖
- Wear Rate of Materials in Unlubricated Rubbing Contact Using a Thrust Washer Testing Machine, Test for (05. 用止推垫圈试验机测定在非润滑摩擦接触中材料的磨损率的试验(05。
- Huakong Automobile Parts is specialized in Engine Bearing, Thrust washer, Bushing, Tensioner for than 30 years old. 温州华康汽车配件有限公司专业生产汽车轴瓦、止推片、衬套、涨紧轮，有30多年的历史。
- This movement is produced by gearing and linkage between the steering wheel in front of the driver and the steering knuckle (or wheel). 这一运动是由装在驾驶员前面的转向盘与转向节(车轮)之间的转向器和连杆装置来共同完成的。
- Wheel shaft, wheel rim, gear, gear ring, con-rod, crankshaft, steering knuckle, steering arm, cam flange, spindle etc. 轮轴、轮毂、齿轮、齿圈、连杆、曲轴、转向节、转向节臂、垂臂；突缘、十字轴等异形件；轴类零件等锻件及主、被动齿轮成品。
- The results showed that alloy layer peeling of thrust washer was mainly caused by poor adhesion between alloy layer and steel back. 结果表明，造成止推垫片合金层产生剥落的主要原因是合金层与钢背之间的结合强度较低；
- Based on the analyses, the forging process for a steering knuckle has been designed. 在此基础上，进行转向节锻造设计。
- Install the pinion mate gears and thrust washers. 安装小齿轮配合齿轮和止推垫圈
- The results show that the thermomechanical treatment can improve the quality of the automobile steering knuckle. 结果表明,锻造余热淬火工艺对汽车转向节质量有明显改善。
- Standard Test for Wear Rate and Coefficient of Friction of Materials in Self-Lubricating Rubbing Contact with a Thrust Washer Using the Micro-Tribometer mod. 标准测试的磨损率和摩擦系数的材料的自润滑摩擦接触推力洗衣机使用微摩擦国防部。
- The hub and bearing assembly does not require removal from the steering knuckle to replace wheel attaching studs in the hub and bearing assembly. 更换轮毂及轴承组件内的车轮固定螺桩无需自转向关节中取出轮毂及轴承组件。
- "The steering knuckle then supported through Ball joints, by upper and lower control arms which are attached to the car frame. 转向节通过球头节与安装在车架上的上下控制臂相连。
- Macro and micro structure of the fractured steering knuckle arm was examined by optical microscope and scanning electron microscope. 采用光学显微镜和扫描电镜对断裂转向节臂的宏、微观组织进行了分析。
- A steering knuckle is the key component in cars, which needs high requirements in dimensional accuracy and product quality. 摘要轿车转向节是轿车上的关键零件，对尺寸精度和产品质量要求很高。
