您要查找的是不是：
- steel backing plate 钢背板
- Why the new rotary backing plate? 为什么说它是新的旋转底盘?
- Rough surface in front and back plate. 前面与后面支承板表面粗糙。
- Damaged back plate across the width. 后固定盖板在宽度方向上破损。
- Wider back plate to cylinder settings. 后罩板到锡林的隔距宽。
- All wire burned sections are to be mounted in hardened tool steel with hardened backing plate. 所有的线割入子必须安装在热处理的模板上并有热处理后的支撑板。
- Variation in setting between back plate and cylinder. 后固定盖板和锡林隔距差异大。
- When mounting thrust washers care should be taken that they are correctly positioned, i. E. The steel backing should abut the housing wall. 安装推力垫圈时,应注意正确定位,即钢背衬应紧靠轴承座壁。
- The rooler pressurizes and the copper back plate adjustment is controled by the flowing tubing head pressure ,as well as steel shaving knife adjustment,The machine can be used on the pperation board. 本机由油压控制辊筒加压、铜挡板的调节以及钢刮刀的调整，可在操作面板上控制使用。
- The results showed that alloy layer peeling of thrust washer was mainly caused by poor adhesion between alloy layer and steel back. 结果表明，造成止推垫片合金层产生剥落的主要原因是合金层与钢背之间的结合强度较低；
- On the sintering friction material, heat fatigue cracks were not found in steel back coat of Ni or coat of Ni followed . 烧结摩擦材料，无论是采用镀镍还是镀铜再镀镍的钢背都没有在镀层处发现热疲劳裂纹。
- PEEK steel backing lubricating composite material applied to high load was prepared.The tribological performance and the microstructure of the material were studied. 研制了一种适用于高负荷条件下运行的PEEK背衬型自润滑复合材料,考察了该材料的摩擦学性能及显微结构。
- What this means is the auger, (the threaded part to which the backing plate attaches), is driven directly off the electric motor. 它是一个螺丝钻（背面有图案装饰的）可直接切断电源。
- The results showed that the segregation of Pb atoms in the interface between the alloy and the steel back was the main factor leading to the failure of the bearing bush. 结果表明 ,铅原子在合金层与钢背材料结合面上的聚集是导致轴瓦失效的主要原因。
- The new "Easy Buff" Rotary Backing Plate is technology borrowed from our OEM Polishing System used at the car factories. 新的旋转底盘是借助于OEM抛光系统在汽车制造厂使用的技术。
- The backing plate shall be welded with matching electrodes so that the weld on the clad side is flush with the backing plate surface. 底板用配套焊条焊接，使复层侧的焊缝与背衬板表面齐平。
- As an alternative to a hard backing plate, this cushioned backing plate distributes pressure for smoother buffing and minimizing swirls. 作为可更换的硬底盘，这款缓和底盘冲击的底盘可以在进行平滑抛光和减到最小程度螺旋纹时减少压力。
- The gauze disc (6) serves to hold the coiled wick tightly against the fuel charge, while the back plate (10) protects the washer. 纱网盘(6)用于保持导火索盘紧靠燃料块，后盘(10)用于保护垫圈。
- That boat is done with the steel plate. 那艘船是用钢板做的。
- Hardened backing plates are required under all pads that bottom out. 最底下的那块垫板后应该加一块热处理背板。
