您要查找的是不是：
- But when it was more than 10, the effect of repeated dismounting times on both bi-screws holding and static bending strength was on the contrary. 但当重复拆装次数大于10次以后，随着拆装次数的增加，构件的静曲强度和双螺钉握钉力均呈现显著下降的趋势。
- The proper quantity of water selected may increase the static bending strength and decrease the transfiguration of plates. 选择合适的水分可以提高板材静弯曲强度,减小板材变形。
- Through analysing sunflower-stem filled plate structure and the stress due to static bending load on it. We have derived a formula for calculating the static bending strength, Here eletric-measure method is ued to check the accuracy of this formula. 本文通过对葵花杆填充板结构分析,静弯曲受力破坏应力分析,推导出了填充板静弯曲强度的理论计算式,通过电测法进行了验证。
- (4) With the increase of repeated dismounting times, both the bi-screws holding and static bending strength reduced. （4）随着塑木构件重复拆装次数的增加，双螺钉握钉力降低，构件的静曲强度也降低。
- static bending strength 静曲强度
- The results indicate that the oxido-decarbonisation on the surface makes the static bending yield strength decrease by 15%. 结果表明，表面层的氧化脱碳使静弯屈服强度降低15%25左右；
- Regular results were achieved from these tests.Compared with the static test, the bending strength, initial elastic modulus and crazing straining were larger in dynamic test. 通过对全级配混凝土构件的静动态弯拉试验，得出了有规律的成果。
- Stiffness It is a measure of the bending strength of paper and board. 挺度是衡量纸和纸板耐弯曲的强度性能。
- It was founded that the best bending strength was 422 MPa when aids was 18 wt%. 在助剂含量为18wt%25时，抗弯强度最大为422MPa。
- In this test, air-dry woods of China-fir, Taiwan acacia, Lauan and Hemlock were used to monitor AB counts under static bending test. 本试验以杉木、相思树、柳桉及铁杉之气乾材为试材，测定静力弯曲试验时AE发生之情况，探讨AE发生次数与应力、应变之关系。
- At transition region,the sea ice bending strength reached the maximum value. 海冰的弯曲强度随着应力速率的增加，经过延性、过渡和脆性三个阶段，在过渡区，海冰的弯曲强度达到最大值。
- Five specimens for three-point static bending tests, five for thickness swelling (TS) were cut from each board according to ASTM D1037-96. 五件样品为三个点的静电弯曲测试 , 五因为厚度增大 (TS) 从依照美国材料试验学会 D1037-96 的每董事会被减低。
- Optimum wearresistance,high bending strength and high resistance to bonding. 耐磨性较好、较高温的抗弯强度和抗粘结能力。
- In this paper the structure of the Joint 15 presented, the principle of pneumatics and method of control are described and the static bending model of the joint is analyzed. 给出了关节的结构，介绍了手指关节的气动原理与控制方法，并分析了关节弯曲变形的静态模型。
- The wood is moderately hard and strong with high bending strength, shear strength and stiffness. 这类木材硬度适中而强壮，具有高度弯曲力、剪力和硬度。
- The Bending strength for concrete bonding was over 7MPa with ester crete-p and 8Mpa with Epcrete-p. 用epcrete p粘合的混凝土试件的抗折强度可达到 8MPa以上 .
- General bone mineral density (GBMD), femur bending strength (FBS), serum-BGP and urine-Hyp/Cr were measured. 进行相应处理后分别测定各组大鼠全身骨矿物密度(GBMD)、右侧股骨抗弯强度 (FBS)和血清骨钙素 (BGP)、尿羟脯氨酸 (U -Hyp)与肌苷 (U -Cr)。
- The hardness of the sintered YT15 alloy was 92 1 HRA and bending strength 1351 9MPa. 烧结后的合金硬度为92 1HRA、横向断裂强度为 135 1 9MPa
- The coated twisty blade patterns possesses higher bending strength and hardness than the uncoated ones. 带涂层可熔扭曲叶片模具有更高抗弯强度和硬度,可以适应制芯操作。
- The Izod impact strength, the bending strength and tensile strength were tested. 同时,测试了该材料的冲击强度、弯曲强度和拉伸强度。
