您要查找的是不是：
- specific bonding strength 比结合强度
- Bond strength is an important parameter for wafer bond. 键合强度是关系到键合好坏的一个重要参数。
- The bonding strength of vapor deposited hard films are measured by this meth... 但人们在膜基结合的测试技术上仍有困难。
- The bond strength experiment of dogtooth exposed to pulsed Nd: YAG laser[J]. 引用该论文 朱建中;黄炜;许肖杰;林斌;陈钰清;顾锡荣.
- Xeno III Adhesive provides bond strength comparable to total etch systems. 异种三胶粘剂粘结强度可比提供总额蚀刻系统。
- Instead some of the double-bond electrons become delocalized, shared among several atoms rather than localized in a specific bond between two atoms. 有些双键里的电子四处游移，由许多原子所共有，而非停留在两个原子间的特定一根键上。
- Indirect methods to measure the interface bond strength include the interlaminar shear strength test. 测量界面粘结强度的间接方法包括层间剪切强度试验。
- Glue Hard brittle brownish solid made by boiling hides and bones.Dissolves in hot water with good bonding strength. 通过煮沸处理动物皮和骨骼而获得的硬而脆的褐色固体。它溶于热水并具有良好的粘合性能。
- The ARB technique not only increased greatly the bonding strength of TA1/Q235 clad plate,but also thinned the microstructure of Q235 plate. 结果表明采用累积叠轧焊方法不仅可以大幅度地提高TA1/Q235的结合强度,而且还可以获得连续均匀、组织细化的Q235的结合组织。
- Glue: Hard brittle brownish solid made by boiling hides and bones.Dissolves in hot water with good bonding strength. 动物胶:通过煮沸处理动物皮和骨骼而获得的硬而脆的褐色固体。它溶于热水并具有良好的粘合性能。
- Finally, the bond strength of FRP bars to epoxy resin and cement grout is also studied. 同时对纤维塑料筋与水泥装和环氧树脂的粘结强度也进行了探讨。
- This paper analysed the influence of specimen thickness on test results of surface bonding strength of thin MDF. 分析比较薄型中密度纤维板试件在检测时组合厚度的改变对其表面结合强度测试结果的影响。
- The conclusion which the bonding strength is obviously influenced by the interlaced yarns. 得出空气变形丝对涂层织物的剥离强度具有显著影响的结论。
- Iong open time, high bonding strength。 Dissociative form aldehyde content can meet national standard. 开放时间长，强度好。游离甲醛含量通过国家标准。
- The influences of ultrasonic power on heavy aluminum wire wedge bonding strength were investigated. 超声功率是影响粗铝丝引线键合强度的最主要因素之一。
- A new method for measuring bonding strength between electroplated layer and substrate of diamond tool is proposed. 摘要提出一种新的电镀金刚石工具镀层与基体结合强度测试方法。
- Objective: To study the influence of dry or wet dentin bonding surface on wet bonding strength. 目的:研究牙本质表面的干燥或润湿状态对牙本质湿粘结强度的影响。
- If we are unable to remove the oxide coat even it is reluctantly soldered the bonding strength is very weak. 如果我们未能将氧化层除去，即使勉强沾上焊锡，其结合力量也是非常弱的。
- There exist the weak interfaces bonding strength between the vinylon fibres and matrix material. 纤维和基体间界面结合强度较弱。
- The layer is smooth with higher microhardness, corrosion and bonding strength by using the proper process. 在合适的电刷镀工艺下,镀层表面平整、光滑,具有较高的显微硬度、耐蚀性和结合强度。
