您要查找的是不是：
- solution treatment time 固溶时间
- Faster: it drammatically reduces treatment time. 更快:它能大大减少治疗时间。
- PrDlonged treatment time adversely edict outcome of radiotherapy for NSCLC. 总疗程时间延长将导致NSCLC放疗疗效的降低。
- The longer the heat treatment time, the easier the recrystallization. 热处理时间越长，则再结晶越容易发生；
- HT Sub-factory : complete process of annealing, quenching, tempering, quenching and tempering, solution treatment etc. 热处理厂：可完成退火;正火;回火，调质;固溶处理等工艺.
- Adding elements of Zr and Cr can increase the tensile strength, and electric conduction can be improved by solution treatment. 同时,铬和锆的存在可提高合金的抗拉强度;采用固溶处理使合金具有高导电性能。
- The optimized treatment time of AZT was 48 h, and the optimized concentration of AZT was 20 mmol/L. AZT抑制癌细胞生长的最佳作用时间为48h,最佳作用浓度为20mmol/L;
- Intermetallic compound foam reinforced aluminium alloy surface composite layer are obtained by solution treatment after low pressure Casting. 通过低压铸造后固溶处理的方法，获得了网状金属间化合物增强铝合金表面复合层。
- A,found a certain high pressure,treatment time and temperature could efficiently enhance the solubility of R. A在水中溶解性之间的关系;发现一定的压力、加压时间和温度可以有效地提高R.
- During the fast cooling process of solution treatment, nonequilibrium segregation of manganese was produced at austenite grain boundaries. 在固溶处理时快速冷却过程中锰在奥氏体晶界产生不平衡偏聚。
- Basic function,and add two Phototherapy(blue light)unit,LED display timer,display treatment time and total time. 在基本配置上：增加双蓝光治疗装置，LED数显计时器,显示治疗时间和累计时间。
- After the homemade welding building of the lead liquid pool of austenitic stainless steel,solution treatment is demanded. 奥氏体不锈钢铅液池进行国产化制作,要求焊接后进行固溶处理,固溶处理后经探伤发现焊缝上有大量的裂纹。
- Basic function,and add:Phototherapy(blue light)unit,LED display timer,display treatment time and total time. 在基本配置上：增加蓝光治疗装置，LED数显计时器,显示治疗时间和累计时间。
- The -phases almost all soluble in -Mg after solution treatment and the mechanical properties improve slightly while the grain size tends to coarsening. 合金经固溶处理后 相几乎完全溶于 -Mg固溶体，但晶粒尺寸有粗化倾向，合金的力学性能略有提高。
- Once the recrystallization stopped, microstructure would not change during further heat treatment time. 再结晶过程结束后，继续延长热处理时间，晶粒组织不发生明显的变化。
- After the solution treatment(20h),the Mg_(17)Al_(12) phase is almost dissolved,but the black particle quasicrystal phase is not dissolved and retained stability. 固溶处理(28 h)后,Mg17A l12相基本溶解,黑色的颗粒状准晶相在固溶处理过程中保持稳定而未溶解。 固溶处理对合金的硬度影响不太明显。
- It may take a long time to find a solution to the problem. 也许要花很长时间才能找到解决这个问题的办法。
- Capture the images you need to enhance patient care, increase productivity, and make more effective use of treatment time and resources. 获取您需要的影像,改进患者护理水平,提高工作效率,更有效地使用治疗时间和资源。
- The high temperature near-solvus pre-precipitation following higher temperature solution treatment were performed on LC52 and Quansi 7039 aluminum alloy. 研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。
- Under these conditions, COD removal rate can reach about 80% within 90 min of treatment time and the wastewater can become clear in 1 min. 在此条件下 ,废水COD去除率可达 80%25左右。 在上述的O3 发生器放电功率、UV功率、废水循环流速条件下 ,处理 1min时废水变澄清
