您要查找的是不是：
- Feature: Anti-bending of hose body, small bending radius, good stiffness, with or without metal fittings available. 特性:管体耐曲挠、弯曲半径小、挺性好。带或不带金属接头。
- Excellent pliability, flexibility and elasticity and suitable for special occasions requiring small bending radius. 本产品具有极好的弯曲、柔软性和弹性,可用于弯曲半径较小的场合。
- Small bending radius, simplified busbar framework, clear arrangement, easy mounting. 弯曲半径小，母线架构简明，布置清晰，安装方便。
- Excellent pliability，flexibility and elasticity and suitable for special occasions requiring small bending radius. 本产品具有极好的弯曲、柔软性和弹性，可用于弯曲半径较小的场合。
- Plastic deformation theory application in pipe bending with small bending radius 塑性变形理论在小半径弯管中的应用
- Numerical simulation of the internal pressure bending process of small bend radius aluminum alloy tubular parts 铝合金小弯曲半径管内压推弯成形过程的数值模拟
- FEM Simulation of Internal Pressure Bending Forming Process for Stainless Steel Tube With Small Bend Radius 不锈钢小弯曲半径管内压推弯成形过程有限元模拟
- FEM modeling and experimental of NC bending process of thin-wall tube with large diameter and small bending radius 大口径薄壁小弯曲半径数控弯管有限元建模和实验
- 2) Excellent pliability，flexibility and elasticity and suitable for special occasions requiring small bending radius. 本产品具有极好的弯曲、柔软性和弹性，可用于弯曲半径较小的场合。
- The bending radius of the hose fitting should not be too small. 软管接头部位转弯不要过小,应大于软管内经8倍以上。
- small bending radius 小弯曲半径
- The bending radius should not less than 15 times of cable diameter. 电缆弯曲半径:不小于电缆外径的15倍。
- The bending radius should not be less than 25 times of the cable diameter. 电缆弯曲半径：不小于电缆外径的25倍。
- TUBE DIAMETER SHALL BE WITHIN 10% OF NOMINAL DIAMETER WITHIN BEND RADIUS. 管直径须在直径理论值和折弯半径的10%25以内。
- Allowed bending radius not smaller than 6 times of its outer diameter, laying temperature not lower than 0. 电缆允许弯曲关径应不小于电缆外径的6倍,敷设温度应不低于0。
- The bending radius of a cable should not be less than 10 times of the cable diameter. 电缆弯曲半径不小于电缆外径10倍。
- The bending radius reduces with increasing length of the mainstream line, and then tends to be relatively stable. 随主流线长度增加，弯曲半径不会无限制减小，将会趋于某一相对稳定状态；
- Permissive bending radius of cable should be no less than 20 times of external diameter of cable. 3电缆的允许弯曲半径不小于电缆外径的20倍。
- For the same amount of bending angle, the springback increase linearly with the increase of bending radius. 对于一定的弯曲角度，零件端部回弹量随弯曲半径的增加而线性增加；
- Moreover, the presence of adhesive improves bending resistance, meanwhile it results in an early failure of the extrusions at a small bending rotation and angle. 界面粘接提高了填充结构的抗弯刚度，但使结构易在较小转角下发生破坏。
