您要查找的是不是：
- shear strength of hull 剪切强度
- The results show that the shear strength of COF is higher than that of COG. 结果表明 :COF比 COG的剪切强度高 .
- The shear strength of the composite is improved above to 11 MPa from 5.5MPa. 改性后碳 /聚芳基乙炔复合材料的剪切强度由 5 5MPa提高到 11MPa以上
- The shear strength of COG and COF bonded with ACF is studied by impact test. 摘要采用冲击试验方法研究了各向异性导电胶膜(ACF)互连的玻璃和柔性基板上倒装芯片（COG和COF）的剪切结合强度。
- The melting point and the shear strength of Bi-Pb-Sn-Cd fusible alloys were determined by DSC and tension tester. 利用差热分析仪和拉伸试验机;研究了易熔合金Bi-Pb-Sn-Cd的成分对合金熔点和剪切强度的影响.
- The results showed that the shear strength of epoxy bonded joint decreased after it was aged in acid media. 结果表明，环氧胶接接头在酸性介质中老化后，其剪切强度明显降低；
- The results showed that the shear strength of fractal joints decreases nonlinearly as the filling percentage increased. 结果表明，随着充填度的增大，分形节理抗剪强度总体上呈非线性减小。
- HY/PA can improve not only the transverse shear strength of CF/PA but also the longitudinal shear strength of KF/PA. 另外,HY/PA在改善CF/PA的横向剪切强度的同时,也改善了芳纶纤维增强尼龙复合材料(KF/PA)的纵向剪切强度;
- The results show that welding parameters do have influence on the microstructure and shear strength of welds. 结果表明，不同的焊接参数对于钢筋焊接网的剪切性能和组织有不同程度的影响。
- The effects of secondary torsion on shear strength of biaxial flexural reinforced concrete beams are analyzed. 探讨了次生扭矩对钢筋混凝土双向受弯梁抗剪承载力的影响。
- The ship struck a mine 20 miles out of Hull. 船在距赫尔20英里处触雷。
- Piezoresistivity of ECAC may involve proximity effect, microcrack and the staggered arrangements of conductive pass-ways due to shear strength of aggregates. 压敏产生的原因是导电沥青混凝土试件的压缩邻近效应、微裂纹和石料间的剪切力使部分导电通路错位。
- The experiments included compressive strength, flexural strength, shear strength of sand grouts, stability and fluidity of net grouts. 试验内容包括砂浆的单压、抗弯、抗剪强度试验以及净浆稳定性和流动度试验。
- The tightness test of hull valve. 舷旁阀密性提交。
- Using this apparatus shear strength of large-size fissured loess samples formed in different time are tested with different loading methods. 介绍了一种改装的便携式直剪仪,并用该仪器测试了不同形成时期、不同加载方式作用下大尺寸裂隙性黄土样的抗剪强度。
- The flexural strength of EB treated specimen increased while the flexural module and the short beam shear strength changed unobvious. 辐照后复合材料的弯曲强度得到明显提高，但弯曲模量和层间剪切强度基本不变。
- The results showed that tool shape had the most influence on tensile shear strength of spot,welding time was secondary,and then tool shoulder. 试验结果表明,搅拌头形状对焊点剪切强度的影响最显著,其次是焊接时间,搅拌头轴肩直径的影响最小。
- The long war of attrition exhausted the strength of both countries. 这场长期的消耗战耗尽了两国的力量。
- The influences of the toughener and coupling agent on the morphology, thermal properties and shear strength of the adhesive were analyzed. 研究表明：随着增韧剂含量的增加，胶粘剂热分解温度下降；
- The horizontal shear strength of the exterior reinforced concrete beam-column joints is analyzed by the stress of the conterminal beam and column. 摘要针对钢筋混凝土框架结构，根据与框架外节点相连的梁、柱构件的受力状态，分析了外节点核心区所受水平剪力。
