您要查找的是不是：
- Theactuator accepts a position demand signal from a master controller anddrives the 0-70 degree output shaft to the demanded position based onan internal shaft position sensor. 动接受的立场，需求的信号从一个主控制器和驱动器0-70度的输出轴到要求的立场的基础上，内部轴位置传感器。
- shaft position sensor 轴向位移传感器
- REPAIR THE OPEN CRANK POSITION SENSOR SIGNAL CIRCUIT. 维修断开的曲柄位置感知器信号电路。
- One solution is to add a rotor position sensor to the synchromotor. 解决这一问题普遍的做法是加装电机转子位置传感器。
- The insertion of the initial velocity is accomplished by offsetting the motor shaft position prior to the start of navigation. 初始速度的加入可以在导航开始前用预先装走马达轴的位置来实现。
- There only use one position sensor to achieve the dual coils commutator. 该换向电路与双位置传感器一起还能够实现双触发双余度换向。
- General pop-up on basic equipment for the horizontal datum for leveling, when looking for is to determine the pump and motor shaft position of the right. 一般以设备基础上弹出的水平线为基准面进行找平，在进行找正，确定泵与电机轴的正确位置。
- Position sensor to throttle body while guiding rubber fitting over throttle body vacuum nipple. 在节气阀体真空管接头上面操纵橡胶管件时，定位感知器至节气阀体。
- The state observer observes the precise load torque, rotor position and speed with only a low accuracy position sensor. 状态观测器可以利用较低精度的位置传感器来准确观测负载转矩、转子位置和转速。
- There are position sensor windings in addition to armature windings in the motor. 这种电机内部除了电枢绕组以外，还带有位置传感线圈。
- Robot's soft griping function relies on the fine-performance force sensor, position sensor and slip sensor. 摘要机械手软抓取功能的实现，关键在于有性能优良的滑觉传感器。
- Robot s soft griping function relies on the fine-performance force sensor, position sensor and slip sensor. 机械手软抓取功能的实现,关键在于有性能优良的滑觉传感器。
- Width adjustment guide shaft positions are bored and milled to ensure paeallelism of two crossbeams. 调宽导向轴穿过横梁，确保两横梁平行度。
- Supplies the required 5 volt power source to the crankshaft position sensor, camshaft position sensor, MAP sensor and throttle position sensor. 向曲轴位置感应器、凸轮轴位置感应器、MAP感应器以及节气阀位置感应器提供所需的5伏电压。
- The first cylinder would be measured by the trigger cam of crankshaft position sensor and sensor that are installed on the cramshaft axis. 第一缸的检测通过安装在凸轮轴轴线上的凸轮轴位置传感器触发轮及传感器进行测量。
- Furthermore, this dissertation proposes a novel commutation control for the FSTP BLDC motor drive without position sensor. 此无感测控制是侦测两相浮动电压讯号的交越点，以求出转子所需要的换相时机。
- A scheme of linear position sensor controller is presented based on the composite design of CPLD (XC95108) and single chip (C8051F206). 摘要提出了一种基于CPLD(XC95108)和单片机(C8051F206)混合设计的直线位移传感控制器的方案。
- counting shaft position converter 数字式轴位变换器
- The engine operation signals as well as the engine speed can be measured by trigger cam of the crankshaft position sensor and sensor that are installed on the crankshaft axis. 发动机信号同步发动机转速通过安装在曲轴轴线上的曲轴位置传感器触发轮及传感器进行测量。
- The inputs to these systems in many cases are in the form of analog quantities such as mechanical displacements (for instance, shaft positions) or temperatures, voltages, pressures etc. 到在许多情况中的这些系统的输入以例如机器的排水量的模拟的数量形式(例如，柄位置)或温度，电压，压力等等。
