您要查找的是不是：
- They are to rise to the set position. 他们就要起跑了。
- Backup set position used in the restore operation to locate the appropriate backup set and files. 还原操作中用来定位相应的备份集和文件的备份集位置。
- Operate counter-clockwise until the required set position is aligned with the fixed stop. 逆时针方向旋转操作,直到所需要的设置点为止,并且对准固定撞嘴。
- Properly heat -set cloth will revert to its original set position if the temperature at which it was heat -set is not exceeded. 如果织物进行了正确的热定形,当环境温度未超过定形温度时,织物会回到热定形时的尺寸和形状。
- You can set positioning for individual elements on the page. 您可以设置页面上各个元素的定位。
- Special design of rising oilway of shoe tree holder controls completely the shoe tree in the set position in the course of upper-binding. 楦头支架上升油路独特设计,可在结帮过程中将楦头完全掌握在设定的位置。
- Special design of rising oilway of shoe tree holder controls completely the shoetree in the set position in the course of upper-binding. 楦头支架上升油路独特设计，可在结帮过程中将楦头完全掌握在设定的位置。
- The key factors affecting the stagnation point position of L-type pipeline section are the setting position of bellows type expansion joint and the bend angle degree. 影响水平转角管段驻点位置的主要因素为波纹管补偿器设置位置、弯头角度。
- Meanwhile,the position and possibility of downhole complicated conditions occurrence was derived,and the new determination method on setting position for casing prog... 应用实例表明,用随机理论方法确定井下复杂情况是可行和有效的,井身结构设计中必封点的确定原则并不惟一,设计者应根据经验和实际情况加以取舍。
- This lightweight part is ultra-rigid and very strong and features an additional middle Ackerman setting position for even more precise and smoother Ackerman steering set-up. 这是轻量级的一部分，超刚性和很强的功能和额外的中间阿克曼设置的位置，甚至更精确和平滑转向梯形的设立。
- Special design of rising oilway of shoe holder controls completely the shoe tree in the set position in the course of upper-bindign. 6．楦头支架上升油路独特设计，可在结帮过程中将楦头完全掌握在设计的位置。
- No force exerted on jigs or on damageable parts.Work can only be done at the set position of the hoisting ring, support and bucket ears. 吊装时，只能在吊环、支脚、罐耳等规定部位进行，不能使卡子、接管等易损部件受力，以免损坏设备。
- Considering the complex coring situation in Sichuan,it is proposed to popularize the"three joints"and"two jioints" outer core barrel assembly,and the setting position of centralizer on outer core barrel is discussed also. 本文结合四川地区取心复杂的情况,建议推广“三节式”和“两节式”外筒组合,并对扶正器在外筒上的安放位置进行探讨。
- It is now our aim to set up a factory. 我们现在的目的是创办一座工厂。
- VRM ver.2 board of output voltage can use four jumper wires to setting Positive or Negative voltage. 2设计成正、负电源共用形式，也就是说同样一块板子您可以经由跳线随意变换成负电压供电或是正电压供电的形式。
- VRM ver.2 board can use four jumper wires to setting Positive or Negative voltage output. 2设计成正、负电源共用形式，也就是说同样一块板子您可以经由跳线随意变换成负电压供电或是正电压供电的形式。
- It smoothes the lasting areas and upgrade the quality of the shoes.6. ecial design of rising oilway of shoe holder controls completely the shoe tree in the set position in the course of u er-bindign. 6．楦头支架上升油路独特设计，可在结帮过程中将楦头完全掌握在设计的位置。
- In Source view, you can set positioning options in the markup for individual elements. 在“源”视图中,可以在各个元素的标记中设置定位选项。
- She had the sapphire set in a gold ring. 她把那枚蓝宝石镶在金戒指上了。
- Change jumper JP5, JP6, JP7, JP8 set position, change modulating frequency to avoid disturbance of some close radio-frequency, corresponding receiver frequency should be accordance with its set. 改变跨接线JP5、JP6、JP7、JP8设置位置，改变调制频率以避开某些相近的无线电频率的干扰，其对应的接收机调制频率也必须与其设置为一致。
