您要查找的是不是：
- How can it pass the pre-installation self test? 能通过安装前的测试吗?
- Fixed function for routine test mode. 常规试验模式固化功能.
- Under test mode, you run each step individually. 在测试模式下,可以单独运行每个步骤。
- The fixed gas detection system with automatic self test. 具有自我自动校正功能的固定式气体侦测系统.
- The fips driver can't load. The driver failed the algorithm self test. fips驱动程序不能加载。此驱动程序的算法自检测失败。
- Press the Esc key or close the dialog box to end test mode. 按Esc键或关闭对话框以结束测试模式。
- Using Bluetooth Test Mode for Transmitter Test and Physical level Observe. 蓝牙测试模式实现及其物理层观测。
- Once rebooted the PDT should be clear,unless the system actually finds some me?mory problem when doinga self test. 重新启动后，PDT应当空白，除非系统在自检上确实发现有内存问题。
- Patented Vaginitis Self Test Card provide free of charge can be used for genital health cheek. 赠送阴道炎自我女性肾虚如何调理检测卡，对生殖器健康进行定性检查。
- TEST MODE: The solenoid is energized with a fixed duration pulsSubsequent fixed pulses occur when the diaphragm reaches the switch closure point. 测试模式:用一个固定的持续脉冲激活电磁阀。当横膈膜达到开关关闭点时，随后出现固定脉冲。
- Automatic moment limiter has the function of self testing and alarming. 全自动力矩限制器具有自动检测和报警功能。
- With the fast growing portable electronics market and higher need of wafer test, power consumption problem of built in self test (BIST) has attracted more and more considerations. 随着手持设备的兴起和芯片对晶片测试越来越高的要求,内建自测试的功耗问题引起了越来越多人的关注。
- No matter how the dialog box will behave at run time, you can terminate it in test mode by pressing ESC. 不论对话框在运行时的行为如何,您都可以通过按Esc键在测试模式下终止它。
- If you want to run the step for testing, you must promote it to test mode. 如果需要运行这一步骤来执行测试,则必须将该步骤升级到测试模式。
- When you promote the step to test mode, the Data Warehouse Center creates the target table. 当您将这一步骤升级到测试模式时,Data Warehouse Center就会创建目标表。
- Capable of operating various machine tools, can read drawings.Loading mode.With mold, to an independent test mode. 能操作各种加工机床，能看懂图纸.;装模
- This paper presents a segment weighted random built-in self test (SWR-BIST) technique for low power testing. 本篇论文提出了区段加权乱数之低功率自我测试技术。
- Therefore, after you promote a step to test mode, you can make only those changes that are not destructive to the target table. 因此,当您将一个步骤升级到测试模式之后,就只能进行那些不会损坏目标表的修改。
- Function The Pulser Preamplifier can be programmed to inject a sine wave, for the purpose of automated self testing or calibration. 结构脉冲发生器/前置放大器可用程序控制绘制正选波;目的是进行自动化自我监测和校正.
- The Functional Test Mode was also selected so that the full IFX-encoded response was captured in the test results managed by the. 管理的测试结果中捕获完整的IFX编码的响应。
