您要查找的是不是：
- rear bearing bushing 后轴承衬套
- Suggestions on the safe operation of the bearing bush were presented. 就轴瓦的安全使用提出了建议
- bush for rear bearing upper half 后轴承上半部轴衬
- bush for rear bearing lower half 后轴承下半部轴衬
- Install the new upper rear bearing oil seal with the white paint facing towards the rear of the engine. 安装新的上后轴承油封，使白漆面向引擎后部。
- Special design of the rear bearing allows for the exchange of V-belts without the necessity of removing the spindle. 由于后轴承的设计特别,更换三角皮带,无需取下主轴。
- A new structure for fixing the bearing bush of the connecting lever in a crankshaft press is introduced. 针对曲轴压力机连杆上轴瓦的固定问题，介绍了一种新的固定结构。
- The simplified algorithm was applied to fault classifier which classifies steam oscillation fault and bearing bushing looseness fault of turbo-generator set. 依据简化算法实现了二分类故障分类器的参数优化，幷应用于汽轮发电机组的蒸汽激励和轴瓦松动故障的分类器中。
- The bearing bush alloy of Al-15%Pb-4%Si-1%Sn-1.5%Cu (wt%) was prepared by mechanical alloying,subsequently cold-compacted and finally hot extruded. 采用机械合金化、冷压与热挤压法制备了Al 15%25Pb 4%25Si 1%25Sn 1 5%25Cu(质量分数 ,%25 )轴瓦合金。
- In the end, it introduces the development of the bimetallic bearing material and combination technology for bearing bush. 最后介绍了用于轴瓦的双金属轴承材料和复合工艺的发展。
- The pinion shaft runs in porous bronze bearing bushes. 小齿轮轴运行多孔青铜轴承衬套。
- The quantitative analysis and general rule analysis are applied to analyze the questions about bearing bush abrasion of No. 7 unit of Baotou No. 2 Power Plant in this thesis. 本论文以包头第二热电厂%237机组存在的%235轴瓦磨损问题分析作为论文选题，对%235轴瓦磨损的原因进行了定性和定量分析。
- The results showed that the segregation of Pb atoms in the interface between the alloy and the steel back was the main factor leading to the failure of the bearing bush. 结果表明 ,铅原子在合金层与钢背材料结合面上的聚集是导致轴瓦失效的主要原因。
- According to an analysis of the performance matching of the crankshaft body and bearing bush, Fe-C-Si-Al is selected as the powder for the explosive spray coating. 依据对曲轴基体、轴瓦与涂层摩擦副匹配性能的分析 ,选择Fe C Si Al作爆炸喷涂的粉末。
- Over temperature problem occurred on No 1 bearing bush of No 1 steam turbine while it was operating under rated conditions and load in Huaneng Shantou Power Plant. 华能汕头电厂1 号汽轮机在额定参数和额定负荷下1 号轴承的轴瓦温度过高。 主要原因是该轴承承受过大的负载， 部分油膜减薄， 引起瓦温升高。
- By analyzing the damage and leakage of the wicket gate seal for Baishan hydropower plant,it is presented that the main reason of leakage is applying nylon bearing bush. 对白山电站水轮机导叶密封损坏和漏水原因进行了分析,指出了尼龙导叶轴套的不适用是导叶密封漏水、损坏的重要原因。
- countershaft front or rear bearing 副轴前或后轴承
- The contact pair elements between the saddle pedestal and the bearing bushing, as well as between the bearing lining and the trunnion were taken as the boundary conditions in the numerical simulation. 将鞍形座与轴承衬体、轴瓦与中空轴之间建立接触单元作为数值模拟的边界条件；
- Macro examination, metallographic microscope, microhardness tester and X ray diffractometer were utilized to study the failure reasons for connecting rode bearing bush of automobile engine. 采用宏微观检验、显微硬度测定、X射线衍射等方法对汽车发动机连杆轴瓦的失效进行了分析。
- A body of the enemy hung upon their rear. 一伙敌人紧紧地跟在他们的后面。
