您要查找的是不是：
- The CDU design method on VAPS is given. 在满足真实性和可靠性的前提下,给出了基于VAPS的CDU设计方法。
- But their design method is still in groping stage. 但变螺距诱导轮的设计方法还在摸索阶段。
- Design method for the confinement is effective. 同时说明了该设计方法的有效性。
- This paper presents a reliability design method for fatigue strength of steam turbine parts subjected to alternating and mean stess with random variable stress ratio. 本文介绍了应力幅和平均应力之比为随机变量时汽轮机零件疲劳强度的可靠性设计方法。
- Thus, a successful muffler design method is developed. 探索了一种消声器的设计和模拟分析方法。
- Methods: The germination percentage was determined by the completely random design of three replications in room temperature. 方法：采用完全随机设计，3次重复，室温条件测试。
- A VM-Based design method for embedded memory system. 基于虚拟存储的嵌入式存储系统的设计方法。
- Here we utilize the traditional skid-to-turn (STT) design method. 接著将自动驾驶仪代入非线性模式，观察其模拟结果。
- Data were analyzed with completely random design analysis of variance, comparisons among groups were performed with LSD test and Dunnett (double side) test. 数据作完全随机设计方差分析,组间比较用LSD检验和Dunnett(双侧)检验。
- The software development adopts blocking design method. 本装置硬件和软件都采用模块化设计。
- The experiment tested vegetation cover of mosses and vascular plants （lichens were not present） was measured in 1994 and 1995 using a stratified random design. 实验在1994年和1995年用分层随机设计测定了苔藓（不包括地衣）和维管束植物的植被覆盖率。
- The system adopts object-oriented design method by VB6. 本文采用面向对象的设计方法,运用VB6。
- Design method of the HDR damper is also provided in this paper. 论文提出了阻尼器相应的设计方法，以供实际工程参考。
- In the design of articulation hole bolt ,the blur variable and random variable existing at the same time,the blur reliability design method of shear strength and extruding strength are approached. 探讨了在铰制孔用螺栓设计中，模糊变量与随机变量同时存在时，抗剪强度与挤压强度的模糊可靠性设计方法。
- It this paper, a new design method of multilayered mirrors as reflector for soft X-rays is proposed.It based on the traditional recurrence relation method, with calculation of random numbers. 摘要在循环递推法基础上加入随机数运算，得到一种简易、精度高、有较高实用价值的多层发射膜设计方法。
- Two kinds of boiler design methods are developed. 开发了锅炉设计的两种方法。
- Design methods for suspended cutoffs are suggested. 同时给出了悬挂式防渗墙的设计方法。
- This paper presents a dynamic design method in which the failure condition of first passage of response for certain points (DOFS) on the structure to random excitation is regarded as a constraint. 提出一种将结构在随机激励下，某些给定点（自由度）上响应首次超过允许极限而发生破坏的条件作为约束的动力学设计方法。
- This paper describes the design method of broad band coaxial termination load. 本文叙述了宽带同轴终端负载的设计方法.
- A design method and design of structured-model language SML are presented. 提出了一个模型及模型库管理系统的设计方法，还就构模语言SML的设计提出模型。
