您要查找的是不是：
- The results show that the orientations of principal compressive stress and principal tensile stress are NEE and NNW respectively. 结果表明：主压应力为北东东向，主张应力为北北西向；
- Recent tectonic stress field is entirely dominated by the principal compressive stress with the components, whose orientation is in level, approximate level or sideling direction. 该带现今以水平、近于水平兼有一定斜向作用的主压应力为主。
- The result shows that the orientation of principal compressive stress and principal tensile stress is NEE and NNW respectively. The modern tectonic stress field is in keeping with that since Cenozoic era. 结果表明：主压应力为北东东向，主张应力为北北西向，现代构造应力场与新生代以来应力场基本一致。
- maximum principal compressive stress 最大主压应力方向
- horizontal maximum principal compressive stress 水平最大主压应力
- Principal compressive stress orientation 主压应力方向
- The principal compressional stress axis obtaind through focal mechanism solutions show NNE and NW orientations. 由震源机制解求出的主压应力轴为北北东向和北西向。
- principal compressive stress 主压应力
- after middle phase of the late Pleistocene the tectonic principal compression stress orientation changed mainly from NNE to NE,with gradual transformation to near SN direction. 晚更新世中期之后构造主压应力方向则以北北东至北东方向为主变化 ,并有逐渐向近南北向转化的特点。
- principal horizontal compressive stress 水平主压应力
- The compressive stress of general polyamine soft foam plastic is improved with polymer polybasic alcohol . 为了改善普通聚氨酯软泡的压陷性能,采用添加聚合物多元醇,并对照其添加前后的物性。
- Compressive stress is transferred by carrying plate and PBL (Perfo-Bond Leisten) shear connectors. 压应力由承压板及PBL剪力键共同传递，拉应力、剪应力主要由PBL，剪力键传递。
- The coating is of a compressive stress and the base metal is of a tensive stress. 计算结果表明,由于瓷层与金属基体热膨胀系数存在差异,瓷层处于压应力状态,金属基体处于拉应力状态;
- As the radium of pipe increases, the absolute value of the radial stress decreases, and the compressive stress o... 随着管道半径的增大,径向应力绝对值减小,瓷层所受的压应力也减小。
- Earlier stage was NS compressive stress and thereafter EW compressive stress,later stage NS torsion stress. 先期为南北向的挤压应力,其后是东西向的挤压应力作用,后期为南北向的扭动应力作用。
- An applied tensile or compressive stress resolved into a shear component along a specific plane and direction within that plane. 一个实际拉或压应力沿某一特定平面和在该平面特定方向上分解得到的切应力分量。
- Objective To investigate the effect of different diameter powder on setting time and compressive stress of carbonated hydroxyapatite cement (CHC). 目的 检测不同粉体粒径对碳酸化羟基磷灰石水泥 (carbonatedhydroxyapatitecement,CHC)的固化时间和压缩强度的影响 ,为其修复骨缺损提供理论基础。
- The maximum draw stress located on the lingual apex, while the maximum compressive stress located on the lingual crest of the ridge. 最大拉应力位于舌侧根尖部，最大压应力位于舌侧牙槽嵴顶。
- The growth behavior of short through-thickness crack in the residual compressive stress which was introduced by a pressin method was investigated. 摘要用压入法引入残余压应力，以研究穿透短裂纹在残余压应力中的扩展规律。
- The shift of G peak position toward lower wavenumber is because of the releasing of compressive stress in a-C:Cu films by the addition of Cu. 实验结果显示随著铜含量增加，发现粗糙度提高并且表面尖锥数量增加及细化的现象，但铜在膜中分布均匀。
