您要查找的是不是：
- oil pressure adjusting screw 油压调节螺钉
- The high step moves from under the adjusting screw. 使高点从调节螺钉下移动。
- The adjusting screw rests on the high step of the cam. 调节螺钉落在凸轮高点上。
- Turn adjusting screw (1) clockwise to increase the delivery pressure, counterclockwise to lower it. 顺时针方向旋转调节螺丝(1)以增加输出压力，反时针方向旋转降低输出压力。
- To Readjust- Loosen lock nut on the adjusting screw. 重新调节：松开调节螺丝上的锁定螺母。
- To Readjust - Loosen lock nut on the adjusting screw. 重新调节：松开调节螺丝上的锁定螺母。
- Remove compression from spring by turning adjusting screw (1) counterclockwise. 通过反时针方向旋转调节螺丝(1)从弹簧上拆卸压缩件。
- The pressure of scraper is controlled by the air pressure adjusting valve. 配套气压调节阀,控制刮印刀的压力。
- Heavy duty adjusting screw. Adjusting screw is both slotted and knurled. 重型调节螺丝。调节螺丝既有槽也有花纹边。
- Non-contacl device. squeegee/flood bar independent pressure adjusting valve. 刮刀墨刀印刷压力独立调压阀/起网装置等.
- Remove adjuster lever, adjuster screw and spring. 拆卸调整器杆，调整器螺丝和弹簧。
- J. Vertical Shaft Fine Adjustment Screw. 垂直杆微调螺丝.
- Adjusting screws are used to set the switching point whilst under pressure. 调节螺丝用来确定压力的开关点。
- Add fine adjust device for the pressure of foot,without dial on the adjustable screw, more convenience for operation. 压脚压力采用微调装置，压力调节螺钉设有刻度，更加方便操作。
- To replace seat/ stem module shut off supply, loosen locknut and back off adjusting screw. 要更换阀座/杆模块，先关闭供应管道，松开锁紧螺母，退出调节螺丝。
- To readjust reduced pressures, loosen check nut and turn adjusting screw clockwise to raise reduced pressure and counterclockwise to lower reduced pressure. 如果要重新调节压力，则松开锁进螺母，顺时针旋转调节螺丝，提高减压；逆时针旋转，降低减压。
- The casing section mill with the dip soldered pressure adjusting rod was used in 22 wells, and every window cutting operation were carried out once. 现场对比应用表明 ,原使用调质钢调压杆进行套管开窗作业 ,约有 2 7 8%25的井需重复作业 ,采用浸焊调压杆进行 2 2口井的开窗作业 ,均一次开窗成功 ,取得了良好的效益。
- Loosen the adjustment screw, and adjust the length of the link rod. 请拧松调整螺丝，拔出或插入连接杆进行调整。
- Tighten adjustment screw to 3 N·m (30 in-lbs) torque. 拧紧调整螺丝到3 N·m (30 in-lbs)扭力。
- Vacuum table side in &out, easy for printing substrate place.Non-contact device, squeegee/flood bar independent pressure adjusting valve. 平面吸风抬面自动进退;放置印刷工作物更容易，刮刀墨刀印刷压力独立，调压阀/起网装置等.
