您要查找的是不是：
- pressure roller cam 压纸滚轮凸轮
- Roller cam brakes were licensed from Wilderness Trail Bikes. 滚子凸轮刹车授权的荒野径自行车。
- Insufficient pressure in pressure roller. 加压罗拉压力不足。
- The surface of pressure roller is plated by chrome treatment. 压纸辊表面经镀铬处理。
- Graduation: laborer rotating, contact roller cam roller cam bearings taper ribbed support of the curve. 分度:出力轴旋转,凸轮滚子接触滚子轴承式凸轮锥度支撑肋的曲线部分。
- Due to mechanical transmission components are two sets of roller cam bearings can be set up independently timing, prompted plane movements. 由于部件传送机械有两套滚子轴承式凸轮,可独立设置定时,促使平面动作。
- Up-down adjustment of pressure roller is controlled by pneumatic system. 压纸辊之升降以气压控制。
- Taper support Rib: Rib conical taper at the circumferential rib support, in between the cam groove, Roller Cam with the circumference of linear contact. 锥形肋位于锥度支撑肋的圆周上,在凸轮凹槽之间,与凸轮滚子的圆周线性接触。
- Taper support Rib : Rib conical taper at the circumferential rib support, in between the cam groove, Roller Cam with the circumference of linear contact. 锥度支撑肋：锥形肋位于锥度支撑肋的圆周上，在凸轮凹槽之间，与凸轮滚子的圆周线性接触。
- Adjustment for upper corrugating roller, pressure roller, and glue roller, is controlled by pneumatic system. 上瓦楞辊、压力辊及上浆辊升降以气压控制。
- But milling device installed in spring pressure, pressure roller link between roller and run 1.2 Times higher. 但在碾磨装置中设置了高压弹簧;使磨辊与磨环之间碾压力提高1.;2倍。
- Stop: stop rotating output shaft, cam rollers contact roller cam bearings taper ribbed support of the re-direct. 停止：出力轴停止旋转，凸轮滚子接触滚子轴承式凸轮锥度支撑肋的重直部分。
- When the roller mill with a certain ring wear, the length of spring pressure adjusted to maintain a constant link between roller mill on the pressure roller. 当磨辊与磨环达到一定磨损后,调整高压弹簧长度,保持磨辊于磨环之间的恒定碾压力。
- The enterprise gaoming huayi rubber rubber roller products factory has special knowledge within the ranges Pressure roller, Embossing and Embossing as well as Embossing. 压紧辊、印刷辊、压花、滚花和压印章是我们文件中的一部分，请您电话垂询更多信息。
- Roller cam : precision design cam rollers used by the favorite Seiki development of the roller bearings, and its design can withstand heavy-duty. 凸轮滚子：精密设计的凸轮滚子采用由潭子精机开发的滚子轴承，其设计可经受重负荷。
- Mathematical Description of Plane Roller Cam 平面滚柱凸轮机构的数学描述
- Position the fuser film sleeve into heater, and the end of the film with ground ring should be in good contact with the conductive rubber gear of pressure roller or the conductive brush after installation. 请在安装新定影膜前，在塑料架与定影膜接触的部位均匀涂上硅脂，尽量在有棱的地方多涂点，以保证定影膜与塑料架的充分润滑。
- The pressurizing roller contains instant rebounding devices which could avoid abrasion of yarn. 压辊设有阻尼加压和瞬间回弹装置，以避免纱面的磨损。
- Bearing for upper/lower corrugating rollers, and pressure roller, uses high-temperature lubricate grease to keep running smoothly and durably. 上、下瓦楞辊及压力辊的轴承均采用高温润滑脂，以确保轴承寿命、运转顺畅。
- Technical reform for pressure roller of Seydel 拉断机大皮辊的改造
