您要查找的是不是：
- oil pump filter 油泵滤清器
- Taian Wuzhou Oil Pump And Oil Nozzle Co., Ltd. 泰安五洲油泵油嘴有限公司。
- Excavation for fuel oil pump house is in progress. 燃油泵房开挖工作正在进行。
- Activates the auxiliary oil pump. 辅助油泵激活按钮。
- Stop the running of one oil pump of the electric motor. 停止电机一油泵的运转。
- We are looking for supplier of oil pump PARTS brand name CTR. 我们需要求购汽车机油泵，请联系我们。
- The pressure of lube oil pump increases very slowly. 机油泵压力增长很慢。
- Fliteration system oil liquid is attracted a filter first by the fact that accuracy is 150 microns , the dirt is not hurt in order to protecting an oil pump by big pellets. 过滤系统油液首先通过精度为150微米的吸滤器，以保护油泵不被大的颗粒污物伤害。
- Automatic oil pump and fault alarm syster, dygnosis and instructions. 自动注油,自动故障报警、诊断,指导处理。
- BEIJING CITY GUOXING AUTOMOBILE OIL PUMP FACTORY MANUFACTURING CO., LTD. 北京市国兴汽车油泵制造有限公司。
- Exhibits: Forging, brake disc, DrivingShaft, engine, oil pump, Steering Gear. 展品锻件、制动系统、传动轴、水泵、机油泵、转向器。
- In most cars, oil is sucked out of the oil pan by the oil pump, run through the oil filter to remove any grit, and then squirted under high pressure onto bearings and the cylinder walls. 在大部分汽车里，润滑油被吸出油漕和油泵，流过润滑油过滤器，过滤去任何杂质，然后在高压下喷到轴承和气缸壁上。
- AUTO ENGINE PARTS Belt, Camshaft, Cylinder Liner, Cylinder Head & Block, Cylinder Gasket, CRANKSHAFT, CARBURETTOR, Enginer Bearring, Electric Fuel Pump, Fuel Pump, Filter, Oil Pump, Piston, Piston ... 查看“机械及工业制品-泵及真空设备-油泵”:公司信息商品信息供应信息
- Carry the Frontier Filter as a back up on multi-day backpacking trips in case larger pump filters clog or become damaged. 携带Frontier过滤器可作为多天背包旅行的备用，用于大型泵式过滤器阻塞或损坏后。
- Main products: oil tank, oil tube, oiler support, oil pump, oil applying wheel etc. 产品主要结构：油箱、油管、安装支架、油泵总成及涂油轮等组成。
- This paper proposes a design project of the dynamoelectric accelerograph control system of X-aeroengine oil pump modulator. 提出了一种某航空发动机油泵调节器电动油门控制系统的设计方案。
- We also manufacture KQL quick type pneumatic pump filters, especially GQL self-scrape-clean filters which have reached advanced international level. 配套产品有KQL快开式气动隔膜泵过滤机及具有国际先进水平的GQL刮除清理式过滤机。
- The rubber formulation of oil pump bushing was designed by orthogonal testing method design for on NBR(N - 41 ). 选用丁腈橡胶（N-41）为基础胶，利用正交试验法设计出抽油泵衬套橡胶配方。
- The oil pump should be close to the oil tank as possible as it can, the suction height should be no more than 500mm. 油泵应尽量接近油箱,吸入高度不得大于500毫米。
- The oil pump should be firmly fixed; the inlet and outlet pipe should be fastened without loose. 油泵应牢固地加以固定,进出口管接头,不得有松动现象。
