您要查找的是不是：
- Injection mould parting line and sizing spacing parting sequence 注射模的分型面及其顺序定距分型
- Parting line at the acceptable surface. 合模分布在合理可接受的表面。
- Parting line cleared and released properly? 分模线是否正确?
- Parting line locks are required on all molds. 琐模块所有的模具都需要。
- Mould halves requiring accurate alignment of core and cavity, and shut off should have appropriate part line locks. 上、下模需要精确配合或有擦位的地方,模具一定要有直身锁。
- ZHEJIANG RUIAN DONGBO MOULD PARTS CO., LTD. 浙江省瑞安市东波模具配件有限公司。
- The parting line tolerance for gib installation is +.000/-.002. 安装导板的分模线公差为+.;000/-
- Design of electrode parts is directly related to geometry shape of mould part. 电极设计与模具活块有直接的几何相关关系。
- A CAD system for three dimensional electrode of turbo blade mould part is developed in this paper. 摘要开发了一个针对涡轮叶片模具活块的电极零件的CAD系统。
- There is a draw cores mechanism with gear-rack on the moving mould part,the combined and bisected type of slide block construction is... 模具结构紧凑,工作可靠,操作维修方便,成型塑件质量好,生产效率高。
- There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK? 产品的这个位置不能出模,我们打算做行位,在此面上会有分模线,你接受吗?
- Becasue of hand deflashing, please mark the parting line into the drawing, and please let me know then the flash size. 因为手遮光，请将分界线在图中标出来，并告诉确切尺寸。
- The parting line at ends of block should be designed such that any offset is in 1"increments for maintenance purposes on core. 考虑到动模维护需要,封胶面应有1”左右的偏移增量。
- This paper emphatically introduces injection mould design of flagpole coor and CAD/CAM process of its mould parts. 本文着重介绍插旗杆座的注塑模设计及模具零件的CAD/CAM过程。
- Knowledge about possibilities, limitations and the function of all related mechanical operation for manufacturing of designed mould parts. 对已设计好的工件的构成和制造是否具有可行性具有一定的了解。
- The optimization parting direction was determined after all undercut features were distinguished, and the parting line and parting surface were confirmed accordingly. 通过侧凹特征的判别确定模具的优化脱模方向，并确定模具的分型线和分型面。
- According to working experience for many years, give an account of the remarkable problems of machining mould parts with a machining center. 总结多年工作经验,叙述了加工中心模具零件时应注意的问题。
- The selection of parting line,the determination of round sprue runner diameter,the design of round sprue runner shape and pouring gate form were presented. 介绍了模具分型面的位置选择、圆形流道直径的确定、圆形流道形状的设计、浇口形式等。
- Elegant bombazine cloth gives a room infuse warm and downy sunshine. Upper part line with novel and chic blue, green, purple " leaf " , bright beauty. 精美的棉纱织品给房间注入了暖和柔和的阳光。上方衬以新奇别致的蓝色、绿色、紫色“叶子”，明亮漂亮。
- I can probably give them more draft but I still want the round inside the cutouts which means I still want the parting line to be on the inside surface of the part in those areas. 我能给予他们更多的牵伸率;但我仍希望裁断块的内侧圆些;我仍希望分开线在要在那些区域的内侧平面上.
