您要查找的是不是：
- motion control bus 运动控制总线
- Zhuhai Motion Control Motor Inc. 珠海运控电机有限公司。
- Shanghai Motion Control Technology Co., Ltd. 上海摩希机械控制技术有限公司。
- This paper developed an AC servo motion control system based on both RS232 and CAN bus. 本文研究了VC++中的用串口和CAN总线通讯的方法,设计了一种用RS232和CAN总线控制多轴伺服运动控制系统。
- Control principles of motion control chip MCX314 was analyzed. 分析了运动控制芯片MCX314As的控制原理,运用单步插补控制模式和连续插补控制模式,提出实现螺纹切削的几种方法。
- Flat feet need additional motion control and firm heel counters. 平足需要额外的动作控制和牢固的鞋跟。
- The control bus contains various lines used to route timing and control signals throughout the system. 控制总线则包含几条表示路由分时和系统的控制信号。
- The system bus is divided into three logical functions; the address bus, the data bus and the control bus. 系统总线的功能在逻辑上被划分为三部分：地址总线、数据总线和控制总线。
- Key words: Par allel mechanism; BLDC;Motion control; Position analysis. 关键词:并联机构;无刷电机;运动控制;位置分析
- The system bus is divided into three logical functions: the address bus,the data bus and the control bus. 系统总线的功能在逻辑上被划分为三部分：地址总线、数据总线和控制总线。
- The DC servo motors are controlled with motion controller LM629 and motor drive chip LMD18200 based on Pc104 bus. 在PC1 0 4总线控制下 ;应用运动控制芯片LM62 9和电动机驱动芯片LMD1 82 0 0实现了直流伺服电动机的控制 .
- The control bus is used to control the sequencing and nature of the operation being performed. 控制总线用来控制要执行的操作的种类和顺序。
- KDMC-H, based on PCI Bus, a motion controller using DSP (ADSP-21061) and FPGA (EPF6016) to construct the core hardware, is discussed in this thesis. 课题设计开发了一种基于数字信号处理器DSP(ADSP-21061)和现场可编程门阵列FPGA(EPF6016)的PCI总线型运动控制器KDMC-H。
- I2C is a multi-master bus, so any device can be the same as the master and control bus. I2C是多主控总线，所以任何一个设备都能像主控器一样工作，并控制总线。
- The IC control bus information gathering system, which is introduced from Uding-The Netherlands is high tamper-resistant. 总线控制信息采集,抗干扰能力强。
- The motion controller design based on DSP and integrated motion control system. 研制基于DSP的运动控制器,集成化运动控制系统,实现多自由度的协调控制。
- On the design of hardware resource of a PC computer itself and connecting with the Motion Control Card . 在硬件设计上,充分利用了PC机的固有硬件资源,结合运动控制卡,建立了开放式CNC系统的硬件资源。
- Control Bus:Carries the various timing signal used to regulate and sepuence operations,like traffic signals regulate traffic flow during the commuter time. 控制总线：载送用二规范和排列顺序的各种定时信号，就像交通信号在上下班时规范交通流向一样。
- In conventional motion control systems, optical encoders or electromagnetic resolvers are used for this purpose. 在传统的运动控制系统中，通常采用光电编码器或旋转变压器来检测转子的位置和速度。
