您要查找的是不是：
- mold temperature distribution 模具温度分布
- Mold temperature is controlled by water flow in cooling channels. 模具温度可用冷却槽中水的流动来控制。
- The rule of temperature distribution of glass mold during surfacing were measured with G90-SAT thermal infrared imager. 摘要利用G90-SAT红外热像仪测量了玻璃模具喷焊时的温度分布。
- This will reduce and equalize mold temperatures. 这样会降低和均衡模具温度。
- The reasons of temperature distribution in a cumene hydroperoxide decomposition reactor was found by analysis reactor fluid mold, reactionoperating mode and calculations of heat transfer. 通过对现有反应器流型、工况的反应和传热计算分析,找到了CHP分解反应器中温度分布不均匀的原因。
- Steady-state laser heating: estimation of the temperature distribution. 稳定状态的激光加热:温度分配的估算。
- Maintaining the correct mold temperture becomes more important and may justify mold temperature control equipment. 保持模具有适当温度，越来越显得重要，因而配备模具的温度控制设备是完全合理的。
- Flatting of Temperature Distribution in Laser Induced Diffusion Region[J]. 引用该论文 吴云峰;叶玉堂;王兵学;杨先明;秦宇伟.
- Maintaining the correct mold temperature becomes more important and may justify mold temperature control equipment. 保持模具有适当温度,越来越显得重要,因而配备模具的温度控制设备是完全合理的。
- Title： Temperature distribution inside wood during microwave-vacuum drying. 关键词：微波真空;木材;干燥;温度分布
- The effects of casting speed and water flowrate on mold temperature field were discussed. 还讨论了拉坯速度和冷却水流量对结晶器温度场的影响。
- Temperature distribution of monocline laser crystal in operation process[J]. 引用该论文 沈鸿元;张戈;黄呈辉;位民;陈振强.
- With this evaporative cooling approach, the mold temperature is automatically evened out. 与此蒸发冷却的方法，模具温度是自动，最终列。
- The results showed that the warpage decreased with the decrease of mold temperature,nozzle temperature and hold preasure. 结果表明,随着模具温度、喷嘴温度和保压压力的降低,制品的翘曲减小;
- Unstable mold temperature will damage to the forming quality,SMC\SMY can guarantee accuracy within proper mold temperature. 不稳定的模具温度会影响成型品质，SMC\\SMY能精确的控制模具在适当温度内。
- Temperature distribution of the model is obtained, in which "skin effect theory" described in ASME code is verified. 分析了管板模型的温度场分布规律，验证了ASME规范中表皮效应理论；
- In this paper the COS process is simulated through FEM to understand the phenomena of no fusion and lug melt because of mold temperature fluctuation. 本课题通过有限元分析模拟铸焊过程,揭示了由于模温的变动导致的冷焊或过熔的规律。
- The main purpose of this software is to provide a correct initial temperature distribut... 该简化算法运算时间短，可以满足实际应用中对运算时间的要求。
- This evaporative cooling approach to mold temperature control provides an excellent general solution to the problem of achieving uniform mold temperature and precise control. 这蒸发冷却的办法，以模具温度控制提供了一个很好的一般问题的解决办法，实现统一的模具温度和精确的控制。
- The temperature distribution in runner is complex because of the numerous effect factors. 熔体内温度分布较为复杂,影响因素众多。
