您要查找的是不是：
- The results of modeling calculation by PHREEQCI software demonstrate the metals in AMD are present mainly as Men+ and MeSOn-2 4species. PHREEQCI软件模拟计算发现酸性矿井水中金属的结合形态主要为Men+和MeSO4n-2;
- The modeling calculation results indi cated that strata denudation maks the permeation losing amount of oil through a fault to increaes,... 模拟计算结果表明,地层剥蚀使油沿断裂渗滤散失量增大,而使气沿断裂渗滤散失量减小。
- To meet the need of modeling calculation on line,the double CPU system using digital signal processor TMS320C31 and 80c196 microprocessor is designed. 为了满足建模过程的在线运行 ,设计了 DSP处理器 TMS32 0 C31和 80 C196双 CPU硬件系统 ;
- The model calculation and predication show good agreement with the experimental results. 模型的模拟和预测结果与实验值吻合很好。
- Based on the modeling calculation the operation rule and optimatic operation condition for fluidized-bed water gas gsaifier are obtained. 探讨了模型经简化后的数值解法,并进行了模拟计算与分析。
- The tide and the tidal current in Luoyuan Bay can be known from the numerica model calculation. 给出了同潮时线与等振幅线、潮流椭圆、最大潮流及不同时刻潮流场分布。
- The result express: The anastomotic degree of the practice dewatering quantity by mining A set coal and the model calculation result is higher. 结果表明:开采A组煤实际疏干水量与模型计算结果吻合程度较高。
- The variation of volume fractions for static and dynamic recrystallization, and austenite grain size during rolling process are obtained by model calculation. 通过对再结晶动力学模型的解析，得到了静态再结晶、动态再结晶的分数以及奥氏体晶粒在轧制过程中的变化情况；
- Model calculation indicated that the residence time of particles differed greatly from that of gas product, so product distribution from pyrolysis was significantly affected. 模型的计算结果表明，原料粒子和产物气体在反应器内的停留时间有较大的区别，其变化情况对裂解产物的分布有很大影响。
- It is shown that the result of model calculation is very clos e to the measured data, and that further forecast on the tendency of the equipme nt condition could possibly be made by this model. 计算结果表明，预测模型的计算值与实际测定值非常接近，而且可进一步预报设备运行状态趋势。
- On the basis of ASM 1 advanced by IAWQ task group, general modeling program SM-ASM1 is compiled by language VC++ 6.0 and used for stable modeling calculation of modeling case in IAWQ reports, with modeling results close to those of IAWQ task group. 在IAWQ推出的ASM1模型的基础上;利用Visual C++6.;0进行编程;编制了通用模拟程序SM-ASM1;并根据IAWQ课题组模拟案例的数据进行了稳态模拟计算;其结果与IAWQ课题组的模拟结果基本符合。
- Through modeling calculation the distribution of temperature in gasifier along altitude has been obtained.The optimization of operation parameters for coal pressrue gasification on fixed bed has b... 通过模拟计算,得到了气化炉温度沿高度的分布,并讨论了固定床加压气化过程操作参数的优化问题。
- The particle transverse dispersion in the above cited zone can be described with the help of a one dimensional dispersion model. The model calculation results are in very good agreement with experimental data. 循环流化床密相区内颗粒横向扩散可用一维扩散模型来描述 ,模型的计算结果与实验数据吻合很好。
- On the base of large numbers of model calculation and plot analysis, found the general rule of borehole shrinkage under the effect of formation dip, maximal principal stress orientation and maximal horizontal stress orientation. 在大量模型计算求解的基础上,得到了地层倾角、最大主应力方向及最大水平主应力方向对倾斜蠕变地层段井眼缩径影响的一般规律。
- As there is many nondeterministic factors in setting the model, the model calculated above is based on the hypothesize. 由于建立模型时的不确定性因素较多，上面计算的模型是在相关资料的基础上，进行了一定的假设的结果。
- In the model calculations, we optimized molecular geometry of the parent calixarene ligand 1 and its complex with H3O+. 在这计算模型里，我们得出杯芳烃配合体1和联合体H3O+最可能的分子几何结构。
- The results of the thermodynamic model calculation show that the main parameters governing performane are:adsorber type, adsorbent properties and the operating temperatures of the heat pump cycle. 热力学模型分析计算表明,控制系统效率的主要参数是:吸附器的型式和吸附剂性能以及热泵循环的操作温度。
- On the basis of sufficient studies on the methods for fault analysis of power system, a normalization method used in the model calculation of grid simulation supporting platform is found. 摘要在对电力系统故障方法充分探讨的基础上，找出了一种规范化的故障计算方法应用于电网仿真支撑平台的模型计算；
- First PLC system completes AGC operation and feedback control;secondary computer completes model calculation and setup of camber control.The whole system reaches the highest level of the world. 一级PLC系统完AGC的执行与反馈控制,二级计算机完成凸度控制的模型计算和设定,整个控制系统达到了当今世界最高水平。
- Manifold air flow dynamic model calculates air mass flow into the cylinder when work and fuel supply system provides proper fuel in time according to AFR control purpose. 空气动态模型用来计算发动机工作过程中的进气量，并结合空燃比的控制目标使燃油供给系统及时提供适量的燃油，而燃油模型则考虑了油膜的形成对进入气缸的燃油量的影响。
