您要查找的是不是：
- minimum cut length 最小切削长度
- Ratio between Cut Length and Circumference. 裁切长度与裁刀圆周长之比率。
- Variations in thickness of flat rolled electrical steel(coils or cut length). 平面轧辊铁心硅钢（镀锡卷板或者是切割长度）厚度上有变化。
- Based on the analysis of failure factors ,the fault tree of crude oil/gas pipelines is put forward,and each order minimum cut sets, weakness and fault prob... 通过对故障树的分析,求出故障树的各阶最小割集,并确定了长输管道的主要失效形式,提出了提高管道可靠性的措施。
- The theoretic basis of the ECS method is the famous theorem, that is, the maximal flow the minimum cut set theorem, which was presented, by Ford and Fulkerson in 1957. 本文根据运输网络的特点,应用网络流理论基本定律,提出了一种无向网络极大流算法。
- This model uses the theory of the Fussell-Vesely in reliability evaluation to work out the minimum cut sets, and using the minimum cut sets to make the fault tree. 该模型运用故障树分析中的下行法计算架空输电线路的最小割集，并用最小割集理论建立故障树。
- Abstract: The complexity of tree set analysis for network was compared with that of minimum cut set analysis.If was illustrated by an example that the analysis method based on minimum cut set is the best approach for the availability analysis of network. 摘要：对网络分析的树集分析法与最小割集分析法的复杂性进行了比较，并示例说明以最小割集为基础进行网络可用性分析是最佳的技术途径。
- The theory of minimum cut sets and its application in accident analysis are described with emphasis on putting forward the importance analysis of the weighted structure in sequence gradation of the bottom events of the fault tree. 阐述最小割集理论及其在事故分析中的作用，着重提出了对故障树底部事件进行排序分级的加权结构重要度分析法。
- In this paper, four pieces of BCD dial combined together with 8098 single-chip microcomputer are successfully used in medical industrial glass tube synchronism-cut system to preset its cut length. 本文将4片BCD码拨盘同8098单片机连接,成功地应用于医药工业玻璃管同步切割系统中,用以预置玻璃管的切割长度。
- Basic principle and implement method of slab cutting length computation model in No 3 CC of Baosteel are introduced. 摘要主要介绍在宝钢3号连铸机上投运的板坯切割长度计算模型的基本原理及实现方法。
- And the optimal parameters by which the minimum cutting edge radius can be achieved theoretically were calculated by using the multianalysis method. 以最小刃口半径值为目标，使用多元分析方法，获得了最优研磨参数组合，试验验证结果与计算值相符。
- A New Method for the Minimum Cut Problem 一种求解最小割集问题的新思路
- Cutting length optimization(CLO) system can minimize scrap and unplanned slab amount in slab continuous casting,so as to improve the rate of finished products. 利用切割长度优化计算机系统可以在板坯连铸生产过程中使废坯量和非订货板坯产品减到最少,从而提高板坯的收得率。
- The buttonholes programmed by the operator are sewn sequentially;the respective cutting length is allocated fully automatically.This means maximum efficiency,even for short runs. 因此，在完成一种锁眼后无需做其他的调节，机器根据操作人员编制好的程序序列，自动地改变切孔长度进行锁眼，极大程度地提高了生产效率。
- How to Achieve the Limit Thickness of Minimum Cut 如何实现最小切削的极限厚度
- To enhance slab quality and lower cost,two models for slab cutting length optimization and slab quality evaluation are set up based on CCM process and data concerned. 为了提高铸坯产品质量、降低成本,根据连铸机铸坯生产工艺及有关参数,建立了"铸坯切割长度优化模型"和"铸坯质量评估控制模型"。
- Maximum flow minimum cut theorem 最大流最小割定理
- Code is a class of parallel concatenated convolutional codes of the system, when the cutting length for long enough, its performance can be close to Shannon limit. 详细说明： 典型的Turb。码是一类并行级联的系统卷积码，当交织长度足够长时，其性能可逼 近仙农限。-Typical Turb.
- Rose bushes shoot again after being cut back. 玫瑰丛修剪後还能再长出新枝。
- In order not to be late, she cut across the fields. 为了不迟到，她抄近路穿过田野。
