您要查找的是不是：
- By analyzing the optimal diffluent ratio and solder angle of the dies, the maximum stress in the body of improved dies is de-creased effectively. 对模具的分流比和焊合角进行优化并再次模拟，发现分流模的最大应力大大降低。
- The ratio of the breaking stress of a structure to the estimated maximum stress in ordinary use. 间断压力同最大压力的比率。
- The maximum stress of the framework occurred at the node of undersurface of the main hydraulic cylinder mounting boss. 机架最大应力值发生在主油缸安装凸台下表面的节点上。
- The results show that the maximum stress locates at the fillet which connects feeding cover and trunnion. 计算结果表明：左端盖与中空轴的过渡处应力最大，筒体中部应力最小。
- The maximum stress was on the apices and the stress on the cervical part was lower.There was no bent stress. 种植体应力主要为均匀分布的压应力，最大应力位于种植体根尖部，颈部应力相对较小，未见明显弯曲应力。
- Result: QGE could significantly increase the BMD and maximum load, maximum stress YP-load of femora i... 结论:强骨膏能提高去卵巢骨质疏松大鼠的骨密度,增强抗外力冲击的能力,其作用机理可能与其拟雌激素样作用有关。
- Finally, the effects of stiffening and load interaction on the maximum stress of DT joints are discussed. 最后讨论了DT型接头的刚度效应与载荷互作用效应。
- The elastic limit is the maximum stress for which the material acts elastically. 材料产生弹性作用时所对应的最大应力，称为弹性极限。
- The maximum stress occurs near the thermally grown oxide (TGO) layer, and its value increases with the increase of heat transfer coefficients. 在热氧化生成层附近产生了较大的应力，并且主应力值随着换热系数的增加而增大。
- There was no change in maximum stress when the thickness of periodontal membrane of fixed abutment tooth was less than 0.1 mm. 当固定桥基牙牙周膜厚度小于0.;1mm时;牙周膜内应力最大值无变化;
- By analyzing the optimal diffluent ratio and solder angle of the dies,the maximum stress in the body of improved dies is de-creased effectively. 对模具的分流比和焊合角进行优化并再次模拟,发现分流模的最大应力大大降低。
- When the distribution is unknown, it is supposed that all of the unloaded fuzes are subjected to the same maximum stress. 当应力分布规律未知时,假定所有被旋卸的引信都承受了同一最大应力,这样根据应力-强度干涉模型即可方便地求出其可靠度或最大许用扭矩。
- Fatigue strength. The maximum stress level that a material can sustain, without failing, for some specified number of cycles. 疲劳强度:对应某一特定循环次数,材料能承受而不失效的最大应力水平。
- The fracture of stuffing box was caused by fatigue, which resulted from the maximum stress concentration on the centripetal border of the oil hole. 结果表明：材料成分和显微组织均符合要求；裂纹起源于输油孔的侧壁；填料盘的失效模式为疲劳失效，内压在填料盘内部输油孔上产生的应力集中导致了填料盘的疲劳失效。
- Under the condition of deflective load, the maximum stress on the root near the slot of the trapezoidal thread of the tie bar decreased 11.6%. 在偏载作用下，拉杆梯形螺纹牙根在卸载槽处的最大应力降低11.;6%25；
- Fatigue limit. For fatigue, the maximum stress amplitude level below which a material can endure an essentially infinite number of stress cycles and not fail. 疲劳极限:对疲劳而言,最大应力幅值水平,低于该值材料可以承受无限次应力循环而不失效。
- The results of FEA method for cold-bending elbow predicted that the point of maximum stress is transferred from intrados to extrados with the increase of the wall thinning. 并应用有限元方法分析了冷弯弯头的应力状况，得出其最大应力发生点随着外拱处壁厚减薄量的增大而向外拱处转移。
- The plate subjected to underwater explosions was simulated by the finite element program LS-DYNA, then the results were analyzed and the maximum stress was obtained. 采用有限元程序LS-DY-NA对水下爆炸载荷作用下的钢板进行仿真计算，对计算结果进行分析，得到板的最大应力值；
- The monotone property of multivariate function proved that the maximum stress strength point exists on the inner surface of casing under the triaxial stress conditions. 通过实例计算,对比分析了用“三向应力圆”理论与其他几种理论计算的抗挤强度值。
- Stress can be the undoing of so many fine players. 紧张可能是这许多优秀选手失败的原因。
