您要查找的是不是：
- Gas welding equipment - Rubber and plastic hoses assembled for compressed or liquefied gases up to a maximum design pressure of 450 bar 气焊设备。能承受最大检验设计气压为450巴的压缩和液化气用橡胶和塑料软管组件
- maximum design pressure 最大设计压力
- Maximum Design Operating Pressure 最大设计工作压力
- The pressure of sweeping shall not exceed the design pressure of the container or the piping system. 吹扫压力不得超过容器和管道系统的设计压力。
- So round shape of cracks (2C/a =2)was a stable shape when cracks developed on the design pressure. 因而在设计压力下发生裂纹传播时,接近圆形的裂纹形状(即2C/a=2)将是一个比较稳定的形状。
- The seal air fans deliver a design pressure that is above the operating pressure in the flue work. 密封风机能使空气达到设定的压力，此压力应高于烟气在烟道中的运行压力。
- All stream jackets are constructed from carbon steel materials and are welded to the valve body. Design pressure is 300 psi unless otherwise noted. 所有蒸汽套都采用碳钢材料制造,并焊接在阀体上。除非另有指定,否则设计压力均为300 psi。
- Reciprocating pumps and compressors require pressure relief valves when the stalling pressure exceeds cylinder design pressure. 当停转压力超过汽缸设计压力的时候，往复泵和压缩机要求安装安全阀。
- The maximum designed speed is not morethan 50 km/hr, the total work capacity of the engine cylinder is not exceeding 50 ml two-wheeled motor vehicle. 最大设计车速不超过50KM/h、发动机气缸总工作容积不超过50ml的两轮机动车。
- It is confirmed that the sinusoidal gear can be easily undercut with a specific addendum height value decided only by the design pressure angle of the gear. 经讨论和仿真证实;正弦齿条所生成的齿轮在一个特定的齿顶高下最容易发生根切;该齿顶高数值只取决于正弦齿轮的设计压力角.
- MLW Maximum Design Landing Weight 最大设计着陆重量
- MZFW Maximum Design Zero Fuel Weight 最大设计零燃油重量
- Maximum Design Speed for Urban Railways of China 我国城市铁路最高设计速度值研究
- Design Pressure barg , 7.0+F.V. 表示设计压力为：内压7.;0，外压全真空。
- Maximum design flood discharge ofreservoir 在水库大坝设计,水库设计最大泄洪流量
- Can argon arc root welding and manual arc cap welding be substituted with common manual arc welding on seamless steel line pipe below 5mm wall thickness with 9.5Mpa design pressure? 壁厚 5mm以下的无缝钢管用于设计压力9.;5MPa的管线，能否采用普通手工电弧焊工艺代替氩弧焊打底、手工电弧焊盖面工艺施焊?
- The simulations show that 2L-MuRR improves the RRF capacity greatly,over 70%. By using 2L-MuRR,SMT can achieve the same high performance with fewer rename registers,effectively reducing the design pressure on the register file. 模拟实验表明;2L-MuRR显著提高了RRF的存储能力(70%25以上);能以较少的重命名寄存器满足SMT高并行度的要求;有效缓解了寄存器文件的设计压力.
- Accordingly,the least teeth number without undercutting is also decided only by the design pressure angle of the gear,without any relation to the coefficient of addendum height of the gear. 相应的无根切最少齿数也仅取决于正弦齿轮的设计压力角;而与齿顶高系数值无关.
- The maximum load for this lorry is one ton. 这辆卡车最大载重量是一吨。
- In addition, key dimensions, duties and operating and design pressures and temperatures may be listed on the diagram. 此外，关键尺寸、负荷、设计和操作压力以及温度可以在图上列表。
