您要查找的是不是：
- Study on the Methods of Voice Transmiting in Low Speed Rate 语音信号低速率传输方法研究
- low speed rate signal 低速率信号
- DOES THE WIPER MOTOR OPERATE IN LOW SPEED? 雨刷马达在低速运转吗?
- Katajainen had to take off at too low speed. 卡塔雅南不得不以很低的速度起飞。
- Great in drying ability, and it can increase projecting speed rate. 具有高超的干燥效力,增加射出速率。
- Sprinkle the yeast and sugar over the water and mix at low speed. 往水里撒上酵母和糖，用慢速搅拌。
- Population: The aggregate population of Beijing grew at low speed. 人口：全市人口总量低速增长。
- The SL-II's low speed handling was also a welcome surprise. 在下午二-二的低速处理也是一个惊喜。
- ASB is the damage reason in the condition of deformation at high speed rate. 可以说，绝热剪切带是材料高速率变形条件下损伤的原因。
- Add drained raisins. Knead for another 3 minutes at low speed. 加入滤干水分的提子，低速搅拌3分钟，直到完全拌匀。
- Conclusion:Taking the low speed puncture may increase the success rate of scalp vein puncture in neonates,decrease the puncture times,reduce the pain of patients and th... 结论:采用慢速进针法穿剌,可以提高新生儿头皮静脉穿剌成功率,降低复针率,减轻患儿痛苦,减少护理工作量和医院材料消耗。
- Mold filling smoothly with low speed and large flow rate as well as instant pressurization in time conformed to the basic principles of squeezing casting. 论述了以低速、大流量、平稳充填铸型并在瞬间及时增压是挤压铸造的基本原理。
- In a blender, mix all ingredients together on a low speed for 30 seconds. 将所有原料倒入掺和器中，慢速搅拌30秒。
- Population: The aggregate population of Beijing grew at a low speed. 人口: 全市人口总量低速增长。
- And discuss influence of hydraulic press loading in change speed rate pattern and superplasticity forging on parameters. 讨论了变应变速率模式液压机载荷和超塑性锻造影响参数的关系。
- Add black sesame seeds and knead for another 2 minutes at low speed. 加入黑芝麻，低速继续拌均匀大约2分钟。
- Acording to the speed rate of the first group.it has few of symptoms of ear upset or earache,so it is a more suitable pressure speed. 证实了按甲组速率方法加压，发生耳痛等不适证状者极少。因此是比较合适的加压速度。
- The ideal method is low speed centrifugalization and dilution medium. 理想的方法是用低速离心加培养基稀释法。
- But low speed dawdling is not at all what this bike is about, is it? 但低速顸，是不是这回事，这是自行车约，是吗？
- The optimum ball milling parameters were determined: ball gradation is 1:2:4,rotational speed rate is 170rpm, ratio of ball to powder is 20:1 and milling time is 15h. 经过正交试验确定的较优的球磨工艺参数为:磨球级配1:2:4,球磨机转速170rpm,球磨时间15h,球料比20:1。
