您要查找的是不是：
- Simulated by WSI at 5G position, the INCONEL 52M TIG weld passed Liquid Penetrant inspection (LP) and Ultrasonic test (UT) thoroughly, no any defects observed. 经WSI模拟5G位置TIG焊测试,INCONEL52M的TIG 焊缝完全通过液体渗透探伤(LP)和超声波探伤(UT),未发现任何缺陷。
- RELIABILITY OF LIQUID PENETRANT INSPECTION 液体渗透检测的可靠性
- Reference Photographs for Liquid Penetrant Inspection 液体渗透检验的标准参考照片
- Liquid penetrant inspection of metallic surgical implants 外科金属植入物液体渗透检验
- The Application of the Liquid Penetrant Inspection Technique to Motorcycle Frame 渗透探伤技术在摩托车车架上的应用
- Founding - Liquid penetrant inspection - Sand, gravity die and low pressure die castings 铸造。液体渗透检查。砂型,重量压模,和低压压模铸造
- Standard Specification for Steel Castings, Surface Acceptance Standards, Magnetic Particle and Liquid Penetrant Inspection 钢铸件磁粉探伤和荧光渗透检验的表面验收标准
- liquid penetrant inspection 液体渗透检验法
- Procedure for penetrant inspection shall consist of . 液体渗透探伤步骤应包括。
- Liquid penetrant may be used for inspection of defect excavations on all grades. 液体渗透检测可检查所有级别的空洞缺陷。
- Perform red dye penetration inspection. 完成涂红渗透检测。
- Founding. Liquid penetrant inspection. Part 1: sand, gravity die and low pressure die castings. 铸造。液体渗透检验。第1部分:砂模铸件、压铸件和低压模铸件。
- Removal of defects shall be verified by magnetic particle or liquid penetrant examination. 用磁粉或渗透检测缺陷是否清除。
- liquid penetration inspection 渗液检验
- Which of the test part characteristics listed below are normally considered before the specific liquid penetrant test method is selected? 选择液体渗透试制方法时，通常要考虑下面列出的哪些零件特性？
- All attachment areas in ferromagnetic materials shall be examined by the magnetic particle technique, if this is not possible by liquid penetrant methods. 铁磁体材料上所有粘附表面，若不能作渗透检测，可采用磁粉检测方法。
- Ultrasonic detection of defects in heat-affected zones of stainless steel pipe welds is discussed. The feasibility of the method is verified by penetrant inspection of dissected pipes. 本文讨论不锈钢管道焊缝热影响区内缺陷的超声波检测方法;应用着色渗透探伤对解剖后的样品进行了验证;证明超声波探伤法的可行性.
- After the workpiece has been cleaned, liquid penetrant is applied in a suitable manner so as to form a film of the penetrant over the surface for at least 13mm beyond the area being inspected. 渗透：待工件清洁干净后，渗透剂就需要以一种合适的方式施加，以便在超过被检区域至少13毫米的表面上获得一薄层渗透剂。
- self-contained penetrant inspection unit 成套式渗透探伤仪
- This paper explains in details the ablution technology of penetration inspection for workpieces of canned motors and its noticing items. 较详细地介绍了屏蔽电动机工件渗透探伤清洗技术及其注意事项。
