您要查找的是不是：
- The strengthening mechanism of fiber is reasonably analyzed with the comparison of interface stress distributions and failure curves. 通过两种工况下界面应力分布情况和失效曲线的比较,分析了纤维的增强机理。
- interface stress distribution 界面应力分布
- Finite Element Analysis to Interfacial Stress Distribution of Nano-composite 纳米复合材料界面应力场的有限元分析
- Analyses of the stress distribution on the coating/substrate interface indicated that significant errors would be introduced if this test standard were used to determine coating shear bond strength. 通过对涂层/基体交界面上的应力分布的分析表明，采用这一试验方法测定涂层剪切结合强度将会造成较大的误差。
- The internal stress distribution of the bead under interference fit and the pressure distribution at the bead rim interface were obtained by using 195/60R14 radial truck tire as example. 以195/60R14规格轿车子午线轮胎为例，获得了胎圈在过盈配合下的内应力分布及胎圈?轮辋接触面上的压力分布。
- Moreover, the 3D stress distribution is more undulant than the 2D one. 相对而言，三维的应力分布曲线起伏较大。
- This method depends on determining the change in stress distribution within the model when it is turned upside down. 倒置法的依据是在模型倒置时测定模型内应力分布的变化。
- Sanders JE. Interface mechanics in external prosthetics: review of interface stress measurement techniques. Medical &biological engineering &computing, 33: 509-516, 1995. 黄健，拘束边界之曲面多样化编修应用于义肢承筒数位化设计，国立成功大学机械工程系，硕士论文，2003。
- The effect on the stress distribution will be negligible except in the immediate vicinity of such points. 除了紧靠荷载作用点的区域以外，上述影响均可以忽略不计。
- An axisymmetrical boundary element method is used for the fiber pull-out test model to obtain the stress distributions at the fiber-matrix interface. 本文利用边界元方法对单纤维拔出实验模型进行了计算分析,得到了奇异的应力结果。
- We defined the conditions of the plane stress distribution of thin plates subjected to in-plane forces. 我们定义了承受平面力的薄板平面应力分布条件。
- Stress distribution is determined in a thin conductive plate containing an elliptic hole under the external electromagnetic loads. 摘要给出一种针对含椭圆孔的导电薄板在电磁力作用下的分析方法。
- The phonon field and phason field stress intensity factors and stress distribution at the crack tips are also given. 进一步可以求得裂纹尖端的声子场和相位子场的应力强度因子,由这些应力强度因子求解了裂尖处的声子场和相位子场的应力分布。
- The damping capacity of SiCp-reinforced MMC was simulated dynamically by setting up a new multi-particulate interface model, under the condition of different heat treatments and actual interface stress using finite element method and experiment dada. 采用有限元方法，利用实验的数据，首次通过建立多颗粒模型，在考虑热处理因素、界面实际应力状态等的更加接近实际的条件下，对颗粒增强Al基复合材料的阻尼性能进行了动态模拟。
- Because the bonding damage was common to be observed in test, the interface stress was analyzed using ADINA. The reason of bonding damage was included, and the influent factors of the interface stress were discussed. 最后,针对碳纤维发生剥离破坏的现象较多,本文运用有限元软件对混凝土、胶之间的界面应力以及碳纤维、胶之间的界面应力进行了分析,探讨了发生粘结破坏的原因与发生,并总结了界面应力的影响因素。
- Finite element analysis has been used to calculate the stress distribution in crystals grown by the Bridgman method. 本文用有元分析法计算了 Bridgman 法生长的晶体中的应力分布。
- Objective: To analyse the difference of the stress distribution during mandible to be forced at the midline. 目的:分析不同年龄的下颌骨正中受力时,下颌骨三维有限元分布的差异。
- Conclusion:The established model may be used for the stress distribution of MCD. 结论:该模型可用于上颌全口义齿应力分布研究。
- With similar index, model test’s results predicts antetype structure’s stress distribution. 把模型试验的结果按照相似指标推算出原型结构的应力分布。
- The stress distribution and amount of deformation has been counted under different pavage conditions. 计算不同情况下该种管道的应力分布及变形量。
