您要查找的是不是：
- I'll be broken after making the down payment. 付了头款，我就一文不名了。
- Atalanta break after Inter lose the ball in midfield. Rivalta's shot is blocked, then Sinigaglia sends his follow-up wide of the right post. 亚特兰大在中场断球，里瓦塔的射门被挡，西尼格利亚再射，偏出右门柱。
- I wanted to take a break after staring at the screen for two hours. 盯着屏幕两小时后我想休息一会。
- If the device requires a break after this kind of control. 如果设备的此类控件后需要具有分行符,则此方法在。
- The fitting is vertical to allow for free draining with straight run after quench oil injection for good mixing. 急冷器是立式的，以便急冷油注入后经直管自排，以达到良好的混合。
- You should take a break after watching TV for half an hour. 看电视半小时之后,你应该休息一下。
- Barkis Bittern: Can a heart still break after it's stopped beating? 茸心停止俯跳动挂了辟以颜后还会痛么？
- Ya think we could take a break after that victorious ruckus? 教练,我们都打赢了。你看,咱们能不能休息一下?
- THERE WAS ANOTHER BREAK after Mr.Crepsley and Madam Octa's act. 暮先生和八脚夫人退场后，又有短暂的幕间休息。
- The reasons why surface of workpiece is moistened from bottom to top in quenching and axial hardness gradient is generated after quenching are also given in this paper. 对试验中所观察到的工件表面由底部向顶部逐渐润湿的现象，以及淬火后工件产生轴向硬度梯度的原因进行了解释。
- Just do what's necessary and you can take a break after. 只需做完你份内的活就可以休息了。
- Experimental results show that the AHS alloys can get the best mechanical properties after quenching for 15 min at 530? and aging forShat 185?. 实验结果表明，在530℃，保温15分钟进行固溶处理后，再在185℃时效8小时，AHS合金能获得最佳力学性能。
- The high hardness and toughness in the abrasion resisting steel after quenching and tempering two times is due to bainite formation in the l... 在二次加热淬火回火中出现高硬度、高韧性值,是因为衬板淬火过程中在具备贝氏体生成的冷却速度下生成了贝氏体组织。
- His health broke after years of hardship. 多年的困苦生活使他的身体垮了。
- The clouds broke after the heavy downpour. 乌云在倾盆大雨过后驱散了。
- After quenching and tempering, material H13 steel core bar was broken during alignment There are naphthalene fractures on macroscopical fractures surface. H13钢芯棒毛坯在调质热处理后的校正工序中发生断裂,宏观断裂面出现萘状断口。
- The clouds broke after the storm. 暴风雨过后，云层分开了
- Their good cheer broke after repeated setbacks. 他们的热诚在接二连三的挫折之后消失殆尽
- After quenching and low tempering,it was found that the hardness of surface alloying is up to 1300HV.The hardness value is higher than that of metallurgy HSS. 淬火及回火后表面硬度达到1300HV;超过一般冶金高速钢.
- The friction reduction, wear resistance and antiseizing ability of cutting tools have been improved remarkably by sulphurization carried out after quenching and annealling. 刀具经淬火、回火后再进行渗硫处理可充分发挥减摩、耐磨作用,大大提高刀具的抗咬粘能力。
