您要查找的是不是：
- Injection pressure and holding pressure i. 注射压力和保压压力。
- The calculating formula for the plastics backface shrink pitfall value of the strengthening rib was put forward at considering the processing conditions of injection pressur... 提出了在考虑注塑压力、注射温度、注射速率等工艺条件下,塑料件加强肋背面的缩陷值的计算公式,并找出通过模具尺寸设计进行补偿的方法。
- Injection pressure was 20 pis, 5 sec and power supply was 15kV constant. 自动气压进样;20pis;5sec.
- Injection pressure of J-ELIII series is different from that of JSW's hydraulic machines. 注塑压力与油压系列不同。
- Maximum injection pressure and maximum holding pressure may be restricted due to molding condition. 有的情形下,最大注塑压力,最大保压压力会因成成形条件不同而受到限制。
- Colon hydrotherapy equipment can sustain a regulated and safe injection pressure to permit cleaning water to reach th extremities of the colon. 大肠水疗法设备能够维持一个规范和安全注射压力,让水清洗,以达到末端结肠。
- Increased needle injection pressure was obsered as the olume of PMMA increases and as the distribution of PMMA is in close proximity to the cortical walls. 同时，使用的聚甲基丙烯酸甲酯黏合剂的体积的增加还可以增大融合椎体的强度。
- The pH of buffer was 6.2, and the run-voltage was 7kV. Pressure injection model was used and injection pressure was 2406.25 kPa xs. 运行电压为7kV，采用压力进样方式，进样压力为2406.;25kPa×s。
- In the Common Rail accumulator injection system, the generation of the injection pressure is separate from the injection itself. 在共轨蓄压喷射系统，新一代的喷射压力是分开的，从注射本身。
- The injection pressure and flow rate and the lengths of injection and falloff periods are the key factors to the succession of well test. 注入的压力、排量以及注入和压降段的时间是关系到试井成功与否的关键因素。
- Die inserts, together with the cores which form recesses, must endure the effects of temperature and injection pressure of the molten metal. 与形式隐藏，必须忍受温度和熔融金属的射入压力的作用的核心一起死插入物。
- Compared with the formation water drive reservoir without water-sensitive damage,the injection pressure of water drive in the water-sensit. 影响木钵区块延10油层驱油效率的主要因素是储集岩的孔隙结构非均质性、水敏伤害、注水压力及加压方式。
- Research results show that with application of Mucell,the 10% raw material can be saved,the injection pressure is decreased by 36.7%,the clamp forc... 研究结果表明:采用微孔发泡注射成型工艺可以节省原材料10%25;注射压力降低了36.;7%25;锁模力降低了60
- The results showed that Sauter Mean Diameter (SMD) of biodiesel decreased, as the injection pressure increased and the orifice diameter diminished. 结果表明：随着启喷压力的增加和喷孔直径的减小，生物柴油索特平均直径不断减小；
- Aiming at the feature of filling tube and injection pressure, non-flowback acidizing was developed to ensure the implementation of miscible flooding. 技术应用将会有一定的借鉴和指导意义。
- The process parameters of bladder-assisted RTM, such as the injection pressure, temperature, the bladder pressure, and the pressure-holding time were determined. 研究和确定了气囊辅助RTM工艺条件,如注射压力、注射温度、充压大小和保压时间等。
- Due to high injection pressure of high concentration polymer solution,reducing injection pressure of high-concentration polymer solution with surfactant has been researched. 针对高浓度聚合物溶液注入压力高的实际情况,开展了表面活性剂降低高浓度聚合物注入压力的研究。
- The important factors influencing the screw backpressure, injection pressure, packing pressure and mold clamping force as well as their setting means are presented. 概述了影响注塑机螺杆背压、注塑压力、保压压力和锁模力的重要因素及其设定方法。
- Through field application, the results show that the technology has features of lowering gas injection pressure, deepening the depth of injection point and savi. 油管压力操作气举阀的打开和关闭主要由阀深度处生产压力的大小所决定,因此它与常规套管压力操作阀气举工艺相比,所需注气压力更低。
- Especially,to heterogeneity serious conglomerate reservoir,the control of injection pressure is more important.On the basis of the design of depth profile control paramete... 特别是对于非均质性严重的砾岩油藏来说 ,注入压力的控制显得更为重要。
