您要查找的是不是：
- injection pressure buildup 注入井压力上升
- Closed system pressure buildup precautions installed. 关闭已安装的系统压力累计预防装置。
- Injection pressure and holding pressure i. 注射压力和保压压力。
- A pressure buildup can occur while the car is parked in the hot sun. 当汽车停放在炎热的日光下时，会出现逐渐建立起压力的情况。
- For extra-low permeability gas reservoir, the time for pressure buildup is normally long, sometimes lasts several mouths. 然而，我国有许多气藏渗透率特别低，压力恢复所需时间特别长,有时长达几个月。
- Injection pressure was 20 pis, 5 sec and power supply was 15kV constant. 自动气压进样;20pis;5sec.
- This paper introduces the MBH method for Calculating the average formation pressure of gas well using pressure buildup curve. 本文介绍了利用压力恢复曲线计算气井平均地层压力的MBH法。
- Should flow rate decrease rapidly a pressure controlled surge pilot closes the valve to prevent downstream pressure buildup. 当流速迅速减少时，压力控制的补偿引导装置就关闭阀门，防止下有压力累积。
- Temperature and pressure relief valve -factory provided aSME rated relief valve protects against excessive temperature and/or pressure buildup within the tank. 过热和超压安全阀---厂家在本款热水器上配置通过aSME(美国机械工程师协会)认证的安全阀,当内胆容器内出现温度过高或累积压力过大等异常情况时,进行降温和减压,提供可靠的安全保护。
- Through double flow rate well testing, the reservoir and fluid parameters can be obtained from the data interpretation of the pressure buildup or breakdown in normal shut-in. 这种试井方法不但可以减少因正常关井测压对产油量和注水量的影响,而且可以减缓因突然关、开井造成的套管变形或损坏。
- Injection pressure of J-ELIII series is different from that of JSW's hydraulic machines. 注塑压力与油压系列不同。
- Maximum injection pressure and maximum holding pressure may be restricted due to molding condition. 有的情形下,最大注塑压力,最大保压压力会因成成形条件不同而受到限制。
- Colon hydrotherapy equipment can sustain a regulated and safe injection pressure to permit cleaning water to reach th extremities of the colon. 大肠水疗法设备能够维持一个规范和安全注射压力,让水清洗,以达到末端结肠。
- Increased needle injection pressure was obsered as the olume of PMMA increases and as the distribution of PMMA is in close proximity to the cortical walls. 同时，使用的聚甲基丙烯酸甲酯黏合剂的体积的增加还可以增大融合椎体的强度。
- In isolated instances where carbon dioxide usage is extremely low, heat leak into the tank is sufficient to maintain the contents above 245 psig and a pressure buildup coil is not needed. 在二氧化碳用量极低的隔热场合，泄漏进容器的热量足以使内容物的压力维持在245 psig以上，因此不需要压力积累蛇管。
- When pressure drops to 245 psig, a portion of the liquid is passed through a pressure buildup coil which vaporizes the liquid in the coil, and the resultant vapor is sent to the tank's vapor space until a tank pressure of 255 psig is attained. 当压力降到245 psig时，部分液体流过一个压力积累蛇管，蛇管使其内部的液体蒸发，产生的蒸气送到容器的蒸气空间，直到容器压力达到255 psig。
- The pH of buffer was 6.2, and the run-voltage was 7kV. Pressure injection model was used and injection pressure was 2406.25 kPa xs. 运行电压为7kV，采用压力进样方式，进样压力为2406.;25kPa×s。
- In the Common Rail accumulator injection system, the generation of the injection pressure is separate from the injection itself. 在共轨蓄压喷射系统，新一代的喷射压力是分开的，从注射本身。
- Liquid helium has the potential to solidify air, which can block pressure-relief devices and other container openings. This can result in pressure buildup that may rupture the container. 液氦有凝固空气的潜力，这会阻塞减压装置和其它的容器开口，导致可以使容器破裂的压力积累。
- The calculating formula for the plastics backface shrink pitfall value of the strengthening rib was put forward at considering the processing conditions of injection pressur... 提出了在考虑注塑压力、注射温度、注射速率等工艺条件下,塑料件加强肋背面的缩陷值的计算公式,并找出通过模具尺寸设计进行补偿的方法。
