您要查找的是不是：
- hub reduction gear 轮边减速器
- NAME OF THE COMPANY: Zhejiang Hengfengtai Reduction Gear Co., LTD. 企业名称:浙江恒丰泰减速机制造有限公司。
- HanDe leading products include Hub Reduction Drive Axle, Single Reduction Driving Axle, Steering Axle and Tag Axle etc. totaling 5 series of more than 50 types' products. 公司主导产品有：轮边减速驱动桥、单级减速驱动桥、转向前轴、重型军用越野车驱动桥、挂车承载轴等五大类50多个品种。
- Cooperation Method: Joint-venture or cooperation with Hengfengtai Reduction Gear Co., Ltd. Being the holding company. 引资方式:合资或合作,由恒丰泰公司控股。
- Reduction gear box Drive MS developed designed Muller type fabricated vertical shell. 减速箱驱动MS 改良的混练机型设计，装配直立壳体。
- The reduction gear of the car doesn't work well and should be replaced by a new one. 这辆车的减速器性能很差，可以换一个了。
- Kawamoto, “Wheel motor provided with a reduction gear,” U.S.Patent No.5163528, 1991. 赖介村，电动轮圈马达传动装置，中华民国专利编号第244042号，1994。
- A motor-operated valve suitable for compactly storing a reduction gear in a small space in a rotor. 一种适于将减速装置紧凑地收容在转子内的狭小空问中的电动阀。
- During reassembly, grease the bore of the drive shaft receiving the reduction gear’s output shaft before reinstallation of the clamp ring. 在重组，油脂的膛的传动轴收到减速器的输出轴之前重新安装钳环。
- The spindle motors, each equipped with a speed reduction gear box in compact design, are directly mounted to the machine base. 两个主轴电机各配有一套独立并设计紧凑的减速齿轮箱，且直接安装在机床底座上。
- The existing such problems as the reduction gear damaged, scraper chains broken in operation of embedded scraper conveyor are analyzed. 针对埋刮板输送机在运行中存在的减速机易损坏,刮板链条、传动链条易断链等问题,分析原因,并采取技改措施。
- When the motor speed must, through the reduction gear drive cascading rotary potentiometers, the voltage difference is 0, motor to stop rotating. 当电机转速一定时，通过级联减速齿轮带动电位器旋转，使得电压差为0，电机停止转动。
- The conveyor is driven hydraulically through a flexible coupling and high torque reduction gear at the rubber lagged top end drum. 输送机由弹性联轴节和高扭矩减速机通过带橡胶护套的高端鼓驱动。
- The V belt wheels of noise experimental table of main carriage reduction gear must suit drive ratio,be lightest in weight and least in moment of inertia . 本文论述的三角胶带轮必须满足：传动比要求、重量最轻、转动惯量最小、制造成本最低，故对三角胶带轮采用了多目标优化设计，其优化结果用于试验台的效果令人满意。
- Using a strap pipe wrench, turn stud Item 11 while keeping the drive shaft stationary in order to release the shafting Item 20/11 from the reduction gear’s output shaft. 使用带管扳手，反过来螺柱项目11 ，同时保持平稳的传动轴，以便释放轴系项目20/11从减速机的输出轴。
- Based on the test result of final reduction gear, the causes of failure were brought out by physics-chemical analysis and metallographic analysis on the parts tested. 摘要根据某厂生产的主减速器总成试验结果，通过对失效样品进行理化和金相组织分析，找出了试验样品的失效原因。
- At higher speeds, the reduction gear mechanism rotates slightly in the opposite direction of steering input to subtract from the total steering angle, resulting in a “slower” steering ratio desirable for stable handling response. 而当汽车高速行驶时，减速齿轮装置则反方向轻微旋转，以减小整体转向角度，从而导致“较低的”转向比，提高车辆的稳定性。
- A slot for a key in the hub or shaft of a wheel. 键槽轮子的毂或轴里的键的沟槽
- Final drive is two-stage planetary reduction gear mechanism. It is mounted at outside of steering and braking clutch. Combined sprocket segment is very convenient for assembling, disassembling and service. 终传动为两级行星传动减速机构,装在转向与制动离合器外侧,组合式链齿、拆装,维修极其方便。
- Through analysis the reasons influencing measuring stability have been found out, which are the flexure strain and structure resonance produced by the transmission axle under the function of the gearing-in force of the reduction gear. 虽然与传统的测量方法一致，但经过理论分析，得出了这种测量方式机械结构影响测量稳定性的原因，即传动轴受减速器齿轮啮合力作用産生的弯曲应变和结构谐振对测量精度影响最大。
